Gigabyte GN-WS32L-RH Quick Start Manual Download Page 6

Page: 6 / 43

Data Rates

Transmit up to 150Mbps and auto fallback

Receive up to 150Mbps

Output power

Legacy mode: 18dBm @11Mbps, 14dBm @54Mbps;

HT20 mode: 14dBm @MCS7 (72.2Mbps);

HT40 mode: 14dBm @MCS7 (150Mbps).

Receive Sensitivity

Legacy mode: -86dBm @11b, -71dBm @11g;

HT20 mode: -67dBm @ MCS7;

HT40 mode: -64dBm @ MCS7.

Antenna

Two RF connectors

Regulatory and Environmental Compliance

EMC certification

FCC part 15 (USA)

TELEC

Temperature Range

Operating: 0 ~ 65 degree C, Storage: -20 ~ 65 degree C

Humidity

10% ~ 85% Non-condensing

Software

Driver Windows

2000/XP/Vista

Security

64/128 bit WEP, 802.1x, WPA and WPA2

Quality of Service (QoS)

WMM

Roaming

Seamless roaming among 11b/g/n access points.

Management Utility

Monitors the network situation.

Mechanical

Weight

4.0 g

1.0g

Dimension

29.85 *26.7*3.3 mm

0.15mm

Packaging

Generic, Gigabyte, private labeling optional

Summary of Contents for GN-WS32L-RH












































Search results

Summary of Contents for GN-WS32L-RH

Reviews:

Related manuals for GN-WS32L-RH

Brands by name

Popular brands

Gigabyte GN-WS32L-RH, Quick Start Manual

Search results

Summary of Contents for GN-WS32L-RH

Reviews:

Related manuals for GN-WS32L-RH

Brands by name

Popular brands