manualshive.com logo in svg

Gigabyte GA-Z77X-UD3H, User Manual, Page: 48 / 126

Share
Download
Gigabyte GA-Z77X-UD3H User Manual Download Page 48

- 47 -

BIOS Setup

CPU Vcore/Dram V3.3V/+12V

 

&

 

Displays the current system voltages.

CPU/PCH/System Temperature

 

&

 

Displays current CPU/Chipset/System temperature.

CPU/System FAN Speed

 

&

 

Displays current CPU/system fan speeds.

CPU Warning Temperature

 

&

 

Sets the warning threshold for CPU temperature. When CPU temperature exceeds the threshold, BIOS will 
emit warning sound. Options are: Disabled (default), 60

o

C/140

o

F, 70

o

C/158

o

F, 80

o

C/176

o

F, 90

o

C/194

o

F.

CPU/System Fan Fail Warning

 

&

 

Allows the system to emit warning sound if the CPU fan or system fan are not connected or fail. Check the 
fan condition or fan connection when this occurs. (Default: Disabled)

CPU Fan Control mode

 

&

Auto   

 Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal CPU 

 

fan control mode. (Default)

Voltage 

Sets Voltage mode for a 3-pin CPU fan.

 

PWM   

Sets PWM mode for a 4-pin CPU fan.

 

 

Note: The Voltage mode can be set for a 3-pin CPU fan or a 4-pin CPU fan. However, for a 4-pin CPU 

fan that is not designed following Intel PWM fan speciications, selecting PWM mode may not effectively 

reduce the fan speed.

CPU Fan Speed Control

 

&

 

Allows you to determine whether to enable the CPU fan speed control function and adjust the fan speed.

Normal 

 Allows the CPU fan to run at different speeds according to the CPU temperature. You can 

 

adjust the fan speed with EasyTune based on your system requirements. (Default)

Silent   

Allows the CPU fan to run at slow speeds.

 

Manual 

Allows you to control the CPU fan speed under the 

 

Slope PWM

 item.

Disabled  Allows the CPU fan to run at full speeds.

 

Slope PWM

 

&

 

Allows you to control the CPU fan speed. This item is conigurable only when 

CPU Fan Speed Control

 is 

set to 

Manual

. Options are: 0.75 PWM value /

o

C ~ 2.50 PWM value /

o

C.

1st/2nd/3rd System Fan Speed Control (SYS_FAN1, SYS_FAN2 and SYS_FAN3 

 

&

Connectors)

 

Allows you to determine whether to enable the system  fan speed control function  for the system  fans 
connected to SYS_FAN1, SYS_FAN2 and SYS_FAN3 connectors and adjust the fan speed.

Normal 

 Allows the system fan to run at different speeds according to the system temperature. You 

 

can adjust the fan speed with EasyTune based on your system requirements. (Default)

Silent   

Allows the system fans to run at slow speeds.

 

Manual 

Allows you to control the system fans speed under the 

 

Slope PWM

 item.

Disabled  Allows the system fans to run at full speeds.

 

Slope PWM

 

&

 

Allows you to control the system fan speed. This item is conigurable only when 

1st/2nd/3rd System Fan 

Speed Control

 is set to 

Manual

. Options are: 0.75 PWM value /

o

C ~ 2.50 PWM value /

o

C.

Summary of Contents for GA-Z77X-UD3H































































































































Reviews:

No comments