background image

- 23 -

Hardware Installation

 

Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheat-

ing. Overheating may result in damage to the CPU or the system may hang.

 

These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3 (Fan Headers)

 

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design. 

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is 

the ground wire). The speed control function requires the use of a fan with fan speed control design. For 

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

5)  BAT (Battery)

 

The battery provides power to keep the values (such as BIOS configurations, date, and time information) 

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low 

level, or the CMOS values may not be accurate or may be lost.

CPU_FAN:

Pin No.

Definition

1

GND

2

+12V /Speed Control

3

Sense

4

Speed Control

SYS_FAN1:

Pin No.

Definition

1

GND

2

+12V /Speed Control

3

Sense

4

VCC

CPU_FAN

SYS_FAN2/SYS_FAN3

DEBUG 

PORT

G.QBOFM

DEBUG 

PORT

G.QBOFM

1

1

SYS_FAN1

DEBUG 

PORT

G.QBOFM

1

SYS_FAN2/SYS_FAN3:

Pin No.

Definition

1

GND

2

+12V 

3

Sense

4

Speed Control

You may clear the CMOS values by removing the battery:

1.  Turn off your computer and unplug the power cord.

2.  Gently remove the battery from the battery holder and wait for one minute. 

(Or use a metal object like a screwdriver to touch the positive and negative 

terminals of the battery holder, making them short for 5 seconds.) 

3.  Replace the battery.

4.  Plug in the power cord and restart your computer.

 

Always turn off your computer and unplug the power cord before replacing the battery.

 

Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an 

incorrect model.

 

Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or 

uncertain about the battery model.

 

When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the 

battery (the positive side should face up).

 

Used batteries must be handled in accordance with local environmental regulations.

Summary of Contents for GA-Z77-HD4









































































































Reviews: