Gigabyte GA-MA69VM-S2 User Manual Download Page 38

Page: 38 / 88

GA-MA69VM-S2 Motherboard

- 38 -

English

Onboard Parallel Port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port. (Default value)

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port.

ECP+EPP

Using Parallel port as ECP and EPP mode.

ECP Mode Use DMA

This option is available only when

Parallel Port Mode

is set to ECP or ECP+EPP.

Set ECP Mode Use DMA to 3. (Default value)

Set ECP Mode Use DMA to 1.

Summary of Contents for GA-MA69VM-S2

























































































Search results

Summary of Contents for GA-MA69VM-S2

Reviews:

Related manuals for GA-MA69VM-S2

Brands by name

Popular brands

Gigabyte GA-MA69VM-S2, User Manual

Search results

Summary of Contents for GA-MA69VM-S2

Reviews:

Related manuals for GA-MA69VM-S2

Brands by name

Popular brands