Gigabyte G492-ID0 User Manual Download Page 98

Page: 98 / 108

BIOS Setup

- 98 -

5-4-4

BMC Network Configuration

Parameter

Description

BMC network configuration

Lan Channel 1

Configuration Address source

Selects to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified, Static, DynamicBmcDhcp. Default setting

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.
Please note that the IP address must be in three digitals, for example,
192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time get BMC network
address

Press [Enter] will set LAN mode and Address source and then get IP,
Subnet, Gateway and MAC address.

Summary of Contents for G492-ID0













































































































Search results

Summary of Contents for G492-ID0

Reviews:

Related manuals for G492-ID0

Brands by name

Popular brands

Gigabyte G492-ID0, User Manual

Search results

Summary of Contents for G492-ID0

Reviews:

Related manuals for G492-ID0

Brands by name

Popular brands