background image

Campetto 6 Underfloor distributor system

 

 

Seite 3 / 13 

Created 

01.04.2014 

ROEN 

Modified 

14.09.2020 

ROEN 

Object-ID 

359746 

1  General information 

1.1  Marking concept for hazards and hints 

 

Hazard 

Hazardous situation which will cause serious injury or even death if it is not prevented. 

 

Caution 

Hazardous situation which could cause slight to moderate injury if it is not prevented. 

 

Hint

 

Indicates information which does not concern personal injury, e.g. hints in respect of material damage. 

 

Protective measures 

Increase safety by applying a protective measure. 
 

The CE label confirms that your device satisfies the safety requirements set down in EU Directives 
2006/95/EC and 2004/108/EC. 

 

1.2  Responsibilities of the operator 

-

 

Make sure that this document is always kept in a safe place in a legible form together with the product. 

-

 

Read these instructions carefully before first start-up of the product. 

-

 

This product has been developed and produced exclusively for the use indicated in these documents. 
Every other use, which is not mentioned explicitly, could affect the intactness of the product and/or 
could constitute a source of danger. 

-

 

The manufacturer rejects any liability for damage which has been caused by incorrect or non-intended 
use of the product. 

-

 

In countries, which do not belong to the European Community, the national legal reference regulations 
as well as the standards and regulations applicable in these countries have to be observed for warranty 
of a corresponding safety level. 

-

 

The installation has to be carried out according to the applicable regulations. 

-

 

The manufacturer assumes no liability for inexpert execution of installation as well as deformations 
which may occur during operation. 

-

 

The electric power supply has to be switched off before executing any action on the installation. 

-

 

Exclusively original parts of the manufacturer shall be used for maintenance. Maintenance work may 
be carried out by qualified staff only. 

-

 

All procedures which are not explicitly mentioned by the manufacturer in the instructions are not per-
mitted. 

-

 

The packing material must not be stored within the reach of children as it could be a potential source 
of danger. 

-

 

The product must not be installed in hazardous environments. Flammable gases or fumes represent 
a serious security risk 

-

 

Energy supply of the underfloor distributor has to be protected in accordance with applicable regula-
tions and manufacturer’s details.  

-

 

It must be checked whether the earthing system has been installed properly. The metal parts of the 
underfloor distributor must be connected to this system. 

Summary of Contents for Campetto 6














Reviews: