Giant UGC120S-100 Installation & Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 54

background image

29

GI-IM048En-1013

Be sure to locate the heater such that the exhaust vent and intake piping can be routed through the building and properly terminated.
Different vent terminals can be used to simplify and eliminate multiple penetrations in the building structure (refer to the Venting
Section). The exhaust vent and intake piping lengths, routing and termination methods must all comply with the methods and limits
given in the Venting section, Part 5 of this manual.

When installing a combustion air intake from outdoors, care must be taken to utilize uncontaminated combustion air.

NOTE: To

prevent combustion air contamination, see Table 1

: Contaminant Table.

Take extra precaution to adequately support the weight of vent pipes terminating through the roof. Failure to properly support roof
terminated vent piping could result in property damage, serious personal injury, or death due to flue gas leakage.

«
...
27
28
29
30
31
...
»

Summary of Contents for UGC120S-100























































Reviews:

No comments

Related manuals for UGC120S-100

Brand: AAFIRST Pages: 9

Brand: Gardena Pages: 8

Brand: Laser Pages: 4

Brand: Bartscher Pages: 32

Elmo Rietschle C-VLR 62

Brand: Gardner Denver Pages: 32

Brand: Rinnai Pages: 31

Brand: NuTone Pages: 8

Brand: Lasko Pages: 4

Brand: Masterflex Pages: 67

KOE000010_11_12

Brand: Kasanova Pages: 10

Brand: Pattfield Ergo Tools Pages: 52

Brand: SGS Pages: 10

Smartmax Series

Brand: ubbink Pages: 29

Brand: Lancaster Water Treatment Pages: 14

Brand: Warmtech Pages: 38

Brand: Wacker Neuson Pages: 52

Brand: Backyard Pro Pages: 18

Brand: Kampmann Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands