background image

3

Your safety and the safety of others is extremely important during the installation, operation, 
and servicing of this water heater. Many safety related messages have been provided in 
this  manual and on your water heater. Always read and obey all safety messages. These 
messages will point out the potential hazard, tell you how to reduce the risk of injury, and tell 
you what will happen if the instructions are not followed.

This is the safety alert symbol. This symbol alerts you to potential hazards 
that can kill or hurt you and others. All safety messages will follow the safety 
alert symbol and either the word “DANGER” or “WARNING”. 

Serious injury or death can occur if you do not follow 
the instructions immediately.

Serious injury or death can occur if you do not follow 
the instructions.

SAFETY INFORMATION

DO NOT

 use this water heater if any part has been under water. Immediately call a 

qualified service technician to inspect the water heater and to replace any part of the 
control system and any gas control which has been under water. Failure to follow this 
instruction can result in property damage, personal injury, or death.

Summary of Contents for UG30





















Reviews: