GI.BI.DI AS05920, Instructions For Installation Manual, Page: 13 / 28

UK
SC130 SC130
UK
12 13
CE Declaration of conformity
The manufacturer:
GI.BI.DI. S.r.l.
Via Abetone Brennero, 177/B,
46025 Poggio Rusco (MN) ITALY
declares that the product:
ELECTRONIC CONTROL UNIT SC130
is in conformity with the following EEC Directives:
and that the following harmonised standards have been applied:
• LVD Directive 2006/95/CE and subsequent amendments
• EMC Directive 2004/108/CE and subsequent amendments
• EN60335-1
• EN 61000-6-2, EN 61000-6-3
The Legal Representative
Michele Prandi
Date 15/06/2017
ON ON
STEP-BY-STEP
WITH PAUSE
IN OPENING,
INVERSION
IN CLOSING
AND
AUTOMATIC
CLOSING
Automatic closing enabled
(if DIP8=OFF).
Operation in reply to a PEDESTRIAN
command:
• Gate close: OPEN for 7s.
• During opening: PAUSE
(if DIP8=OFF), the gate stops and the
timer of the automatic closing starts.
STOP (if DIP8=ON).
• Gate open: CLOSE.
• During closing: STOP.
• After a STOP: It is necessary
a command and the motion starts
again in the opposite direction
of the previous motion.
OFF ON
STEP-BY-STEP
WITH STOP
AND
AUTOMATIC
CLOSING
Automatic closing enabled.
Operation in reply to a START
command:
• Gate close: OPEN.
• During opening: STOP.
• Gate open: STOP.
• During closing: STOP.
• After a STOP: It is necessary
a command and the motion starts
again in the opposite direction
of the previous motion. Automatic closing disabled.
Operation in reply to a PEDESTRIAN
command:
• Gate close: OPEN for 7s.
• During opening: STOP.
• Gate open: CLOSE.
• During closing: STOP.
• After a STOP: It is necessary
a command and the motion starts
again in the opposite direction
of the previous motion.
Automatic closing enabled.
Operation in reply to a START
command:
• Gate close: OPEN.
• During opening: PAUSE,
the gate stops and the timer of the
automatic closing starts.
• Gate open: CLOSE.
• During closing: Inverts the motion.
TEST
TRANSMITTERS LEARNING
Push the button P1 for 2 s when you turn it on, the control unit starts in OPEN .
Once reached the OPENING limit switch starts again in CLOSING . Once reached the CLOSING limit switch it stops.
In this way you have the correct control unit/motor operation.
Push the button P1 , the control unit will enter in LEARNING (the led blinks, then turns on fixed), push the buttons
of the transmitter to store:
• START function will be assigned to the first button pushed of a new transmitter.
• PEDESTRIAN function will be assigned to the second button pushed of the same transmitter.
It is possible to store in sequence some new transmitters as long as the led is turned off fixed.
After the learning of last transmitter, it is necessary to wait that led turns off (3s), indicating the system is ready to work
in a normal way.
WARNING : After learning the first transmitter, the system will accept only that family of codes (if the first one
is Rolling, all the transmitters must be Rolling). It can learn 30 transmitters, when you arrive to the 31st the led blinks
because the memory is full.
PEDESTRIAN MANOEUVRE
With the 2nd button learned by the transmitter or DOWN from terminal board, the gate opens for 7 s, a START makes
open all and denies the pedestrian.
COMPLETE CANCELLATION OF TRANSMITTERS MEMORY : Push the button P1 (the led blinks, then turns on)
and keep it pushed as long as the led will blink again and turn off (10s). When you release the button, the led turns on
again, indicating that the system is ready to learn a new transmitter.
LEARNING OF TRANSMITTERS WITHOUT ACCEDING TO THE CONTROL UNIT (ROLLING
TRANSMITTERS)
: Push the buttons UP and DOWN of the terminal board at the same time for 1 s or the buttons
1 and 2 of a transmitter already stored at the same time for 2 s. The control unit will enter in LEARNING and it will be
possible to follow the usual procedure to store the new transmitters.
DISPOSAL
GI.BI.DI. advises recycling the plastic components and to dispose of them at special authorised
centres for electronic components thus protecting the environment from polluting substances.