manualshive.com logo in svg

GHS Corporation Rocktron Patchmate Loop & Floor, Manual

Share
Download
GHS Corporation Rocktron Patchmate Loop & Floor Manual Download Page 20

20

Connections....continued.....

This connection diagram shows how to connect the PatchMate to a MIDI Controller such as the 

Rocktron MIDI Mate (use similar connections for the Rocktron All Access, All Access LTD and MIDI 

Xchange.  

Note:  Internal PHANTOM POWER is provided by the PatchMate LOOP 8 Floor  via the MIDI IN con-

nector pins 6 & 7 and will power your Rocktron MIDI Controller eliminating the need to have a power 

adapter plugged directly into the MIDI Controller.

The power provide is 9VAC.  To use this feature you will need a Rocktron RMM900 MIDI Cable (sold 

separately).  See the Rocktron website - www.rocktron.com for more information.

The PHANTOM POWER feature is provided exclusive to support all ROCKTRON MIDI CONTROL-

LER products.  Please refer to your owners manual before attempting to use this option with a MIDI 

CONTROLLER other than a Rocktron product.  Rocktron can not be held responsible for any damages 

arising from improper use or connections.

Summary of Contents for Rocktron Patchmate Loop & Floor

































Reviews:

No comments

Brands by name

Popular brands

Load more brands