manualshive.com logo in svg

Ghost Controls Ghost Pro LDM2, Installation And Owner'S Manual

Share
Download
Ghost Controls Ghost Pro LDM2 Installation And Owner'S Manual Download Page 51

51

P U S H - T O - O P E N

© G h o s t   C o n t r o l s

®

  2 0 2 0

    WARNING                                                                 

DO NOT SCREW THE OPERATOR ARM IN OR OUT TO ADJUST YOUR GATE POSITION. DOING SO 

CAUSES THE SYSTEM TO NOT FUNCTION PROPERLY.

TURN THE CONTROL BOX OFF

STEP 13. Attach front mount bracket to the operator. The gate must remain in the desired 

closed position.

CLOSE THE GATE TO THE DESIRED CLOSED POSITION

A.  Temporarily assemble the front mount of the gate by inserting the supplied 10mm x 40mm clevis pin, 10mm 

I.D. nylon spacer, and clevis hairpin through the gate bracket.

    NOTE                                                                   

ALTERNATE TUBE GATE BRACKETS FOR MOUNTING TUBULAR GATES. (NOT FOR USE WITH FLAT PANEL 

GATES) see below image. Tube brackets (AXTB) sold separately.

Summary of Contents for Ghost Pro LDM2




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands