Ghost Controls Ghost Pro LDM2 Installation And Owner'S Manual Download

Page: 39 / 67

P U L L - T O - O P E N

CANCELLING AUTOCLOSE TIME ON YOUR GATE

NOTE

Canceling AUTOCLOSE can only be performed when the gate opener is idle.

Cancelling AUTOCLOSE will remove your previous duration setting and force you to pick a new duration the next time

you enable AUTOCLOSE. You can use PartyMode

to temporarily disable AUTOCLOSE and the system will retain your

current AUTOCLOSE duration when PartyMode

is disabled. Turning the control board off will not remove AUTOCLOSE

because turning the system back on will automatically reengage the AUTOCLOSE feature.

A. Press and hold the

SET AUTOCLOSE TIME

button until it beeps.

B. Release the

SET AUTOCLOSE TIME

button. The LED next to the AUTOCLOSE button will start

blinking at the rate of 1 blink per second

C. Within 5 seconds, press and hold the

SET AUTOCLOSE TIME

button until you hear a beep to disable

the AUTOCLOSE feature.

D. The AUTOCLOSE feature is now disabled until you enable it with a new setting. IF THE AUTOCLOSE LED

IS STILL ON, THE AUTOCLOSE HAS NOT BEEN DISABLED (REPEAT STEPS A-B-C).

AUTOCLOSE LED INDICATOR

The AUTOCLOSE LED indicates which mode the gate system controller is currently in. Note, that this LED will turn OFF

after one minute of inactivity to conserve system power.

LED Solid On

LED Blinking On & Off

LED Off

AUTOCLOSE

is enabled

AUTOCLOSE is enabled but temporarily suspended

because PartyMode has been activated. Disabling

PartyMode will turn the LED back to a Solid On.

Assuming system has been active within

the last minute, this indicates that

AUTOCLOSE is disabled.

Summary of Contents for Ghost Pro LDM2




































































Search results

Summary of Contents for Ghost Pro LDM2

Reviews:

Related manuals for Ghost Pro LDM2

Brands by name

Popular brands

Ghost Controls Ghost Pro LDM2, Installation And Owner'S Manual

Search results

Summary of Contents for Ghost Pro LDM2

Reviews:

Related manuals for Ghost Pro LDM2

Brands by name

Popular brands