background image

H69.0.01.6C-02 

 Operating Manual GMH 285 / GMH 285-BNC 

page 7 of 8 

 

 

_____________________________________________________ 

_____________________________________________________________________________ 

 

8  Adjustment 

The instrument can be adjusted, assuming that: Reliable references are available, such as ice-
water regulated precision water baths or similar. 

Displayed value °C =(measured value °C - OFFS) * (1 + slope correction / 100 )        
Displayed value °F =(measured value °F - 32 °F - OFFS) * (1 + slope correction / 100 )       

 

Follow these instructions to adjust the device: 

  Switch the device on. 

  Press 

 and 

 together until 

the first parameter “

0FFS

” is displayed.  

  Set parameter with 

 = up or 

= down  

  Jump to the next parameter by pressing 

Parameter  Value 

Information

 

Key 

 

Keys 

 

 

 

 

OFFSET correction     

factory setting: oFF = 0.0°C

 

OFF

 

No offset correction 

-5.0 

 5.0 

°C  

or 

-9.0

9.0 

°F

 

Value of offset correction 

Slope correction 

factory setting: oFF= 0%

 

OFF

 

No slope correction  

-5.00 

 5.00 

Value of slope correction in % 

Press 

 again to store changed settings, the device restarts (segment test). 

NOTE:

 

If there is no key pressed within the menu mode within 2 minutes, the configuration will 
be cancelled, the entered settings are lost! 

9  Error and System  Messages 

    ----

  

No temperature probe connected 
Or at GMH 285 BNC: cable/sensor broken 
Or at GMH 285:          cable/sensor shorted 

   ERR.  1

 

  Value exceeding measuring range, value too high or cable/sensor broken 

   ERR.  2

    Value exceeding measuring range, value too low or cable/sensor shorted 

   ERR.   7

    System error – the device has detected a system error (device defective or not within 

working temperature) 

  

 

The blinking bAt display indicates low battery voltage, device will continue to work for a 
short time. 

 

  

The battery is consumed and has to be changed. Measurements are no longer 
possible.  

10 Accuracy Inspection: Adjustment /Update Service 

You can send the device to the manufacture or retailer for adjustment and inspection.  
Moreover the manufacturer can do the latest software update. This ensures that future 
improvements are provided to owners of older devices in a cost-saving way. You can display the 
current software version if you do not release the on/off button after you switched the device on, but 
hold it for more than 5 seconds. (i.e. “r. 1.0”) 

Summary of Contents for GREISINGER GMH 285









Reviews: