background image

13

5.4.3  Replacing the blades

IMPORTANT  Blades must be replaced by your 

Dealer.

Blades bearing the code indicated on the chart 

on page 2 should be used on this machine.

Given  product  evolution,  the  above  mentioned 

blades may be replaced in time with others hav

-

ing similar interchangeable and operating safety 

features.

   6.   DIAGNOSTICS 

What to do when ...

Source of problem

Corrective action

1.  The machine will not start or will not keep running

Incorrect starting 

procedure

Follow the instructions

 

(see chapter 2)

Dirty spark plug or incor

-

rect distance between the 

electrodes

Check the spark plug

 

(see chapter 4)

Air filter clogged

Clean and/or replace the 

filter (see chapter 4)

Carburation problems

Contact your Dealer

2.  The machine starts but is lacking in power

Air filter clogged

Clean and/or replace the 

filter (see chapter 4)

Carburation problems

Contact your Dealer

3.  The machine runs irregularly 

and lacks in power when revved

Dirty spark plug

 

or incorrect distance 

between the electrodes

Check the spark plug

 

(see chapter 4)

Carburation problems

Contact your Dealer

4.  The machine makes too much smoke

Incorrect composition of 

the fuel mixture

Prepare the fuel mixture 

according to the instruc-

tions (see chap. 1)

Carburation problems

Contact your Dealer

5.  The blades heat up and give off smoke

Overheating due to poor 

regulation

Contact your Dealer

6.  The blades move with the engine idling

Incorrect carburation

regulation

Contact your Dealer

Summary of Contents for SHT 660 K


















Reviews: