background image

10

5  After using the washer

5.1 Stop 

the 

pressure 

washer

1. 

Stop the engine.

2. Close the tap.
3. Operate the spray gun until 

the wasser is depressurized.

4. Lock the safety catch.

Switching off POSEIDON DE

1. Stop the washer by moving 

the throttle lever to STOP 
position.

2. Switch off the ignition by 

pushing the ON/OFF button. 
The light indicators will now 
turn off.

5.2 Disconnecting 

supply 

lines

1. 

Shut the fuel cock.

2. Remove the water hose from 

the washer.

5.3 

Storing the washer  
(frost-protected)

1. Store the pressure washer in 

a dry room without danger of 
frost.

IMPORTANT!

If the high-pressure washer 
is stored in a room with 
temperatures around or 
below 0°C, anti-freeze should 
be drawn into the pump 
beforehand:

1. Remove the water inlet hose 

from the washer.

2. Remove the lance.
3. Start the washer and stop it 

again after max. one minute.

,

4. Connect the suction hose 

to the water inlet of the 
washer and place it in a tank 
containing anti-freeze.

5. Start the washer.
6. Hold the spray gun over the 

tank containing anti-freeze 
and activate it to start suction 
of anti-freeze.

7. During suction operate the 

spray gun two or three times.

8. Lift the suction hose from the 

tank containing anti-freeze 
and activate the spray gun to 
pump out the remaining anti-
freeze.

9. Stop the washer.

Summary of Contents for POSEIDON 2-31

















Reviews: