background image

6

To reduce risk of fire, electric shock or injury, always follow these basic precautions and 
accident prevention measures when using this appliance, including the below:

INSTALLATION

• 

Heavy:

 The product is heavy, be careful when moving it. To avoid back or other

  injury, have 2 people lift or mechanical aid when installing. 
• 

Damage:

 When unnoxing, thoroughly inspect the appliance carefully for any  

  damage. If there is any damage, do not install the appliance. Contact our  
  support centre on 1300 296 699 for advice.
• 

Protection from moisture:

 Make sure the appliance is installed in an indoor area  

  away from wind, rain, water spray or drips.
• 

Protect from heat:

 Do not place the appliance next to an oven, grill or other  

  source of high heat, or where it will be exposed to direct sunlight for long  
  periods of time.
• 

WARNING: 

Ventilation: 

Make sure to have enough ventilation, keep any  

  ventilation openings, in the appliance enclosure or in the built-in structure,  
  clear all obstructions. Make sure plenty of air circulation around the appliance  
  to prevent overheating.
• 

Level:

 Install appliance level in order for proper operation.

ELECTRICAL SAFETY

• 

Voltage: 

Plug the appliance to a 220-240V, 50Hz, properly earthed power  

  outlet, it must be in good working order. 
• 

Power connection:

 Do not use an adaptor or an extension cord.  

  Plug the power plug directly into a separate power point that cannot be  
  accidentally  turned off, and that is easily accessible so you can switch it off  
  if needed.
• 

Power cord:

 Do not kink or damage the power supply cord. Make sure it is  

  behind the appliance so no one can step on or place anything on the power  
  supply cord or against it. A damaged power plug may overheat and cause a fire.
• 

Damaged cord: 

Do not use a cord that shows cracks or abrasion damage. Any  

  damage to the cord may cause a short circuit, fire and/or electric shock. Contact  
  our support centre on 1300 296 699 for advice
• 

WARNING!

 The light supplied with this appliance cannot be replaced by the user.  

 

Contact the authorised service agent for replacement or service.

 Disconnection:

 Never pull the powercord to unplug appliance. Grip the plug and  

  pull straight out from the power point.
• 

Electrical work:

 If the installation of this appliance requires any electrical work,

  make sure it is carried out by an electrician.

GENERAL SAFETY INSTRUCTIONS (Cont.)

Summary of Contents for GTF372AU70SS





















Reviews: