background image

5

• 

The ONchannel 710 must be charged using the mains adaptor provided.

• 

Using any other adaptor will result in non-compliance with EN60950-1 and will invalidate 

any approvals & warranty.

Î

Î

Place the ONchannel 710 units in the charge cradle in an upright position.
The charge LED indicators will light up.

Î

Î

It takes about 10 hours to fully recharge the batteries if they are 

completely run down.

New batteries take up to 14 hours to fully charge.
Important: 

Always turn off the PMR units when charging. This will shorten the 

charging time.

Î

Î

Charging the battery batteries (using adaptor).
Lift the charge socket cover located on the right side of the 

handset.

Î

Î

Insert the round connector of the 9.0 V DC/300 mA adaptor into 

the charge jack.

Î

Î

Plug the mains adaptor into a 240 VAC, 50 Hz main socket 

with the switch on the socket set to Off. Use only the power 

supply On Real provided to this model. Then switch On the 

main socket.

Charge jack

Mic/spk jack

3.3.1 Battery meter

The battery meter is located in the left corner of the LCD screen. It appears like a battery with three 

bars inside. These indicate the amount of power available. When the battery level reaches it minimum 

level in PMR on mode, unit will emit two beep tones and automatically the unit will power off. 
The ONchannel 710 can detect the battery charge in 4 levels;

Battery charge at high level.

Battery charge at medium level.
Battery charge at low level. At this level, the ONchannel 710 will emit a "beep" sound for 

every 10 seconds in normal mode.
Battery charge at very low level. When the battery level reach it minimum level in 

ONchannel 710 on mode, unit will emit two "beep" tone and automatically turn off the 

power and proceeds to watch mode. 

Important:

 Charge the unit for 10-14 hours.

Risk of explosion if battery is replaced by an incorrect type. Disposed of used batteries 

according to the instructions.

3.3.2 Battery life

The ONchannel 710 has a built in power saver to make the batteries last longer. But when you are not 

using the units, turn them Off to conserve battery power.

main socket

Summary of Contents for ONchannel 710















Reviews: