manualshive.com logo in svg

Geolux RSS-2-300W, User Manual, Page: 32 / 41

Share
Download
Geolux RSS-2-300W User Manual Download Page 32

RSS-2-300W User Manual

29

RSS-2-300W Non-Contact Surface Velocity Radar

Picture 7. Geolux Instrument Configurator Main Window With the Device Connected – Data 

Clicking the Settings button enables the user to configure the surface velocity radar or upgrade 

the device to a newer firmware version. The device settings are grouped into 3 groups: Interfaces, 

Processing and Measurement. By clicking the name of a specific group, all the settings which 

belong to that group can be viewed and changed.  The following settings are displayed::

Interfaces

Baud rate

RS-232 protocol

RS-485 protocol

Device ID

Warm up time

4-20 mA output

4-20 mA min.

4-20 mA max.

Processing

Sensitivity level

SNR threshold

Filter length

Direction filter

Measurement

Velocity unit

PGA sensitivity

Velocity min.

Velocity max.

A detailed description (as described in Chapter 5. along with pictures from of this user manual) of 

the selected setting appears on the right side of the window when the user clicks on, or begins to 

change, a specific setting. When a setting is changed, the Set button will appear next to the setting. 

By clicking the Set button, the user confirms the change and the new settings is saved.

Summary of Contents for RSS-2-300W










































Reviews:

No comments