background image

16

Geo Knight & Co Inc

52 Perkins St, Brockton MA 02302 USA

(508)588-0186 - Fax (508) 587-5108

[email protected] - www.heatpress.com

Limited Warranty

Geo Knight & Co warrants that the press is free from defects in both material and

workmanship One Year from the date of invoice to the buyer. If any parts or workmanship are found to

be defective in manufacture, Geo Knight & Co will repair or replace the defective parts or workmanship.

In addition, Geo Knight & Co warrants that the Digital Knight heat control is free from defects in both

material & workmanship and is covered under no-charge support for (3) years. Geo Knight & Co also

warrants that the heating element is warranted for the lifetime of the press, provided it is owned by the

original purchaser. This lifetime warranty on the heating element does not cover temperature sensor

failure, damage or disconnection. This warranty covers all parts to repair the defects, except when

damage results from accident, alteration, misuse or abuse, or when the machine has been improperly

installed, or modified in any way. If the press becomes defective during the limited warranty period of

one year for the entire press, three years for the control, or the lifetime of the heating element, Geo

Knight & Co reserves the right to recall the defective press to the factory for repairs if on site component

replacement is deemed not possible by Geo Knight & Co. A return authorization must be granted by

Geo Knight & Co prior to its return.

If a press covered by the one year limited warranty must be returned to the factory for

repairs, Geo Knight & Co shall make every effort to repair buyer’s press. However, Geo Knight & Co

reserves the exclusive right to determine whether to repair or replace a defective press. If Geo Knight

& Co authorizes a replacement press, the warranty of the replacement press shall expire on the

anniversary date of the original machine’s invoice to the buyer.

There are no warranties which extend beyond the description on the face hereof. Seller

disclaims any implied warranty of merchantability and/or any implied warranty of fitness for a particular

purpose, and buyer agrees that the goods are sold “as is”. Geo Knight & Co does not warrant that the

functions of the press will meet the buyers requirements or expectations. The entire risk as to use,

quality and performance of the press lies with the buyer. In no event will Geo Knight & Co be liable

for any damages, including loss of profits, destruction of goods or any other special, incidental,

consequential or indirect damages arising from the use of the press or accompanying materials. This

limitation will apply even if Geo Knight & Co or its authorized agent has been advised of the possibility

of such damage.

Summary of Contents for Digital Knight K20S

















Reviews: