background image

 

 

Page: 4 of 16

 

Copyright © 2013 GenTent Safety Canopies, LLC – All Rights Reserved 

V5 – July, 2013 

Limited Three Year Warranty

 

 

What is Covered

 

This warranty covers any defects in materials or workmanship of the GenTent™ Safety Canopy 

under normal use in winds up to sixty mph and snow loads up to eighteen inches, with the 

exceptions stated below. 

 

How Long Coverage Lasts 

This warranty runs for three years from the date on your GenTent™ product receipt. 

 

What is not Covered 

This warranty does not cover issues resulting from improper installation or issues resulting from 

not adhering to the Warnings and Cautions as stated in this GenTent Product Installation and  

Safety  Manual.  This warranty does not cover fading or discoloration caused by exposure to 

sunlight or chemicals, or deterioration due to exposure to chemicals.  This warranty does not 

cover abuse, misuse, or neglect including, but not limited to, lost parts, over tightening clamps, 

blocking a running portable generator exhaust with parts of the GenTent, or rips, tears or breaks 

due to sharp and/or heavy and/or falling objects.  This warranty does not cover issues arising as 

a result of modifications made to your portable generator or to the GenTent™ that have not 

been specified by the manufacturer.   

 

GenTent products or components returned without an RMA and proof of purchase are not 

covered (see How to Get Service).  Also, consequential and incidental damages are not 

recoverable under this warranty. Some states do not allow the exclusion or limitation of 

incidental or consequential damages, so the above limitation or exclusion may not apply to you.  

 

 

What GenTent Safety Canopies LLC Will Do 

GenTent Safety Canopies, LLC will repair any GenTent canopy or replace any GenTent frame or 

clamp component that proves to be defective in materials or workmanship during the term of 

this Warranty.  In the event repair of a GenTent canopy is not possible, GenTent Safety Canopies 

will either replace your GenTent canopy with a new GenTent canopy of similar composition and 

price. 

 

How To Get Service 

Contact GenTent Safety Canopies LLC by emailin

[email protected]

,  calling 

781-334-8368

 

or writing us at the address below to discuss your Warranty concern and obtain a RMA (return 

materials authorization).  You must provide a copy of the original receipt or packing slip that you 

received as part of your purchase.    

GenTent Safety Canopies, LLC 

Attn: Customer Warranty Service 

44 Gile Rd 

Nottingham, NH 03290 

 

How State Law Applies 

This warranty gives you specific legal rights, and you may also have other rights which vary from 

state to state.

 

Summary of Contents for StormBracer

















Reviews: