Genie Z-45J Operator'S Manual Download Page 32 | Manualshive

Page: 32 / 74

background image

Operator's Manual

Fifth Edition • First Printing

Controls

30

Z

®

-

45J DC • Z

®

-45J Bi-Energy

Part No. 1297032GT

Ground Control Panel

1

Platform rotate switch

Move the platform rotate
switch to the right and the
platform will rotate to the
right. Move the platform
rotate switch to the left
and the platform will rotate
to the left.

2

Turntable rotate switch

Move the turntable rotate
switch to the right and the
turntable will rotate to the
right. Move the turntable
rotate switch to the left and
the turntable will rotate to
the left.

3

Primary boom up/down switch

Move the switch up and the
primary boom will raise.
Move the switch down and
the primary boom will lower.

4

Primary boom extend/retract switch

Move the switch to the left
and the boom will extend.
Move the switch to the right
and the boom will retract.

5

Used for optional equipment

6

Bi-Energy models: Engine idle (rpm) select
switch

Move the switch to the left (turtle) for low idle.

Move the switch to the right (rabbit) for high
idle and quickest battery charging.

7

Auxiliary power switch

Use auxiliary power if the primary power
source fails.

Simultaneously hold the auxiliary power switch
on and activate the desired function.

8

Key switch for platform/off/ground selection

Turn the key switch to the platform position
and the platform controls will operate. Turn the
key switch to the off position and the machine
will be off. Turn the key switch to the ground
position and the ground controls will operate.

9

Red Emergency Stop button

Push in the red Emergency Stop button to the
off position to stop all functions. Pull out the
red Emergency Stop button to the on position
to operate the machine.

10

Platform overload indicator light

Light flashing indicates the platform is
overloaded and no functions will operate.
Remove weight until the light goes off.

11

Hour meter

The hour meter displays the number of hours
the machine has operated.

12

Bi-Energy models: Glow plug switch

Move the glow plug switch to either side and
hold for 3 to 5 seconds.

«
...
30
31
32
33
34
...
»

Summary of Contents for Z-45J











































































Reviews:

No comments

Related manuals for Z-45J

Brand: ubbink Pages: 7

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16

Brand: Gage Pages: 36

Brand: AXEM Technology Pages: 31

Brand: Feig Electronic Pages: 35

Brand: Weldability Pages: 12

AutroMaster ISEMS

Brand: Autronica Pages: 94

Brand: National Instruments Pages: 4

Brand: Real Time Devices Pages: 45

Weighing System

Brand: NAUSICAA Pages: 16

Brand: SPT Plasmateknik AB Pages: 15

Brand: Kuzar Pages: 24

Brand: AUTEC Pages: 37

Brand: stertil-KONI Pages: 154

Brand: Fenix Pages: 2

Brand: Magnum Pages: 18

Brand: Geberit Pages: 28

Brand: GEA Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands