Genie TZ-50 Operator'S Manual Download Page 48

46 

Genie TZ-50 

Part No. 133555

Operator’s Manual

Third Edition • Third Printing

Continuous improvement of our products 
is a Genie policy. Product specifi cations are 
subject to change without notice or obligation.

Specifi cations

Height, working maximum 

 

16.9 m

Height, platform maximum 

 

15.1 m

Height, stowed maximum 

  

 2 m

Horizontal working reach  

  

8.9 m

maximum from centerline of machine 

 

Outrigger footprint 

 

4.37 m x 4.37 m

Maximum load capacity 
ANSI and CSA 

 

227 kg

CE and Australia 

 

200 kg

Width, stowed 

 

1.68 m

Length, stowed 

  

6.7 m

Turntable rotation 

 

359° 

Platform rotation  

 

160° 

Platform dimensions 

 

 1.1 m x 68 cm

Platform leveling 

 

self-leveling

AC outlet in platform 

 

standard

Tire size,  

225/75 R15 

ANSI, CSA and Australia models 

Load Range D

Vibration value does not exceed 2.5 m/s

2

Whole body vibration value does not exceed 0.5 m/s

2

Tire size, CE models 

215/70 R14 

 

Load Range C

Ground clearance 

 

25.4 cm

Weight 

See Serial Plate

(Machine weights vary with option confi gurations)

Maximum towing speed 

 

97 km/h

Maximum tongue weight 
ANSI, CSA and Australia 

 

202 kg

CE  

105 

kg

Hydraulic pressure, maximum 

 

207 bar

(boom functions) 

 

System voltage 

 

24V

Airborne noise emissions 

 

Sound pressure level at ground workstation 

89 dBA

Sound pressure level at platform workstation 

86 dBA

Guaranteed sound power level  

 

105 dBA

Power source

Models without drive option 

4 Group T-105

 

 

6V DC 225AH Batteries

 

 

with optional Honda 

 

 

GX160K1 Gas Engine

Models with drive option 

 

4 Group T-145

 

 

6V DC 244AH Batteries

 

 

with optional Honda 

 

 

GX160K1 Gas Engine

Floor Loading Information (ANSI / CSA / Australia)

Tire load,  maximum 

 

957 kg

(without rated load) 

Outrigger load, maximum 

 

1286 kg

(including rated load) 

Tire contact pressure  

 

3.5 kg/cm

2

(without rated load)

 

 

347 kPa

Outrigger contact pressure  

 

2.0 kg/cm

2

 

(including rated load) 

 

197 kPa

Occupied fl oor pressure 

 

846 kg/m

2

(without rated load) 

 

8.30 kPa

Occupied fl oor pressure 

 

127 kg/m

2

(including rated load) 

 

1.25 kPa

Floor Loading Information (CE)

Tire load,  maximum 

 

1035 kg

(without rated load) 

Outrigger load, maximum 

 

1286 kg 

(including rated load) 

Tire contact pressure  

 

3.8 kg/cm

2

(without rated load)

 

 

375 kPa

Outrigger contact pressure 

 

2.0 kg/cm

2

(including rated load) 

 

197 kPa

Occupied fl oor pressure 

 

1002 kg/m

2

(without rated load) 

 

9.83 kPa

Occupied fl oor pressure 

 

127 kg/m

2

(including rated load) 

 

1.25 kPa

Note: Floor loading information is approximate and does 
not incorporate different option confi gurations. It should 
be used only with adequate safety factors.

Summary of Contents for TZ-50



















































Reviews: