Genie GS-2668 RT Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 46

background image

Operator's Manual

Fifth Edition · Second Printing

Part No. 133534

GS-2668 RT • GS-3268 RT

17

Ground Control Panel

1 Hour meter

Indicates the number of hours the machine has

been put into use.

2 Engine start button

Press this button to start the engine.

3 Gasoline/LPG models: LPG select button with

indicator light

Press this button to select fuel. Light on

indicates that LPG is selected. Light off
indicates gasoline is selected.

4 Engine idle select button with indicator light

Press this button to select the engine idle

setting. Light on indicates high idle is selected.
Light off indicates low idle is selected.

5 20 amp circuit breaker for controls circuit

6 LCD readout screen

7 Gasoline/LPG models: Choke button

Press this button to activate the choke.

Diesel models: Glow plug button

Press this button to activate the glow plugs.

8 Platform up button

Press this button and the platform will raise.

9 Lift function enable button

Press this button to activate the lift function.

10 Emergency lowering function enable button

Press this button to activate the emergency

lowering function.

11 Emergency lowering down button

Press this button to activate the emergency

lowering down function.

12 Platform down button

Press this button and the platform will lower.

13 Key switch for platform/off/ground selection

Turn the keyswitch to the platform position and

the platform controls will operate. Turn the
keyswitch to the off position and the machine
will be off. Turn the keyswitch to the ground
position and the ground controls will operate.

14 Red Emergency Stop button

Push in the red Emergency Stop button to the

off position to stop all functions. Pull out the red
Emergency Stop button to the on position to
operate the machine.

Controls

«
...
17
18
19
20
21
...
»

Summary of Contents for GS-2668 RT















































Reviews:

No comments

Related manuals for GS-2668 RT

Brand: Enerpac Pages: 151

Brand: Titan Lifts Pages: 30

Brand: GMG Pages: 30

Brand: GMG Pages: 40

Brand: GMG Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands