ⓒ
2020
LaON
Technology Co., Ltd. All rights reserved.
64
A Out, B Out, C Out, D Out’:
Turn the left rotary control (#10) to set the
Line output gains from -20 dB to +6 dB (default 0 dB). To confirm
the selected settings, press right rotary control (#16) to return to the main menu or rotate to scroll to the next
item.
Set ISS800 menu
GN ELECT DYN:
In the menu, select Electret (ELECT) or Dynamic (DYN) to set the type of Gooseneck microphone.
To save the selected setting, press rotary control or scroll to the next item.
Call Tone on off:
In the Call Tone menu, select On (enable) or Off (disable). When enabled, the user can hear the tone when a
call occurs. To save the selected settings, press rotary control or scroll to the next item.
Low Cut off -3 -6:
In Low Cut menu, you can set the cutoff level of low-frequency audio such as wind noise and air conditioning.
The maximum cutoff level is -6dB.
VOX Level:
To set the VOX level.
If the audio level of the Talk channels is higher than this level, the audio is detected, and the Talk key LEDs
flash green. The same level applies to Ethernet Beltpack.
Selection range: 0: disable, 1 through 9 (From -58dB to -10dB)
Latched Talk:
The user can set on the Talk key that the latch is enabled or disabled. If each Talk channel number is selected, the latch
can be enabled. If the latch is disabled (Momentary) the Talk path is only open while the Talk key is pressed. If the latch
is enabled, quickly tapping the Talk key will latch a key, and a second tap will release it.
Sidetone Option:
Track (default): The sidetone level will track the master volume level.
Non-track: The sidetone level is fixed to the set level.
If sidetone level is set to zero, it is muted.
A 4-Wire 2-Wire
B 4-Wire 2-Wire:
Before using a Line, Line type should be set to ensure that the volume level and the call signal operate normally.
In the menu, select 2-Wire or 4-Wire to set the type of the Line A or Line B. To save the selected setting, press
rotary control or scroll to the next item.
Screen Save:
Set the time period when the screen will automatically turn off.
Selection range: 10 to 900 minutes (10 minutes per step)
The display will turn off if key is not used or there is no incoming call during a set time period.
A G12345
B G12345
C G12345
D G12345:
Line audio routing:
Set the GENIE group channels on the Lines (Line A through Line D).
In this menu, use the rotary control (#16) to navigate to each number and press rotary control (#10) for setting.
You can set up a single or multiple GENIE group channels on each Line. Once the GENIE group channel is set
on the Line (4-wire, 2-wire, AUX), it is possible to communicate with all devices set to the same group channel.
The user can also set one Line without setting up a GENIE group channel on the Talk key.
Note:
If a GENIE group channel is set on the Line, set the GENIE group channel on the Talk key and do not
set the Line on the Talk key. In this case, setting the Line on the Talk key may distort the sound.
Note:
In Speaker Station, if a GENIE group channel is set to a Line, one talk/listen path is occupied. Even if
two GENIE group channels are assigned to a Line, one talk/listen path is occupied.
If the GENIE group
channels are assigned to the A, B, C and D Lines, four talk/listen paths are occupied.
GN ELECT DYN
Call Tone On Off
LowCut Off -3 -6
VOX Level 1
Latched Talk
1 2 3 4 5 6 7 8
Sidetone Option
Track Non-Track
A 4-Wire 2-Wire
B 4-Wire 2-Wire
Screen Save 900
A G12345
B G12345
C G12345
D G12345
OPTO1 T12345678
OPTO2 T12345678
Talk1 LaON001 11
Talk2 LaON001 12
Talk3 LaON001 13
Talk4 LaON001 14
Talk5 LaON001 15
Talk6 LaON001 1R
Talk7 LaON001 21
Talk8 LaON001 22
