background image

7

Wall Mount

Anchors (as needed)

Perforated Angle 

Mount

STEP 5

Mount and Power Aladdin Connect™:

1.  Using the DCM mounting bracket as a template at the optimal 

Wi-Fi location. Mark and drill 2-3/32” pilot holes and mount 

bracket to wall using supplied screws. If mounting to drywall, 

use anchors provided in kit or if mounting to perforated angle 

at opener location, use nuts, washers and screws provided. 

2.  Plug Power Pack into wall outlet. An extended screw is provided 

to secure Power Pack to outlet if needed.

3.  Plug Power Pack into back of DCM as shown in 

STEP 1

.

NOTE:

 LEDs on DCM will flash momentarily as it reacquires signals.

4.  Snap DCM onto mounting bracket.

5.  Route wires and secure with supplied staples.

6.  Affix the warning placard next to wall control or DCM in plain 

sight to signify that the door will operate remotely.

STEP 6

Mount DPS Module to Garage Door:

DO NOT remove the battery “

PULL TAB

” from DPS until directed by the app.

The DPS should be mounted on the TOP door panel only. Mount to steel reinforced end 

stile on the far left or right under the top hinge. DO NOT mount to unreinforced door panel.

1.  Clean door where DPS will mount.

2.  Install double sided tape to back of mounting bracket and affix to door.

NOTE: 

Double sided tape is designed to hold bracket in place temporarily only. Not to be used for permanent 

mounting.

3.  Pre-drill 2 - 3/32 holes. DO NOT drill all the way through door.

4.  Use included self tapping screws to mount DPS bracket to top door panel end stile.

5.  Slide DPS down onto mounting bracket. DPS should snap onto bracket.

NOTE: 

The DPS included with this kit is already programmed to the DCM. See the NOTE under 

STEP 7 

regarding additional sensors (DPS).

END STILE

Garage Door

Garage Door

Mounting DPS 

Sensor

112612.0001

WARNING

AVERTISSEMENT

MOVING DOOR can cause serious 

injury or death.

MOUVEMENT PORTE peut causer des 

blessures graves ou la mort. 

STAND CLEAR!

Door could close automatically.

Do Not stop or stand in doorway

SE TENIR À L'ÉCART DE LA PORTE!

La porte pourrait se refermer automatiquement.

Ne pas arrêter ou debout dans la porte.

1

2-4

6

Summary of Contents for Alladin connect









Reviews: