manualshive.com logo in svg

Genex CT-D201, User Manual

Share
Download
Genex CT-D201 User Manual Download Page 3

2.4GHz DIGITAL CORDLESS TELEPHONE  with CID     

MODEL: CT-D201                                  

USA V ERSION

 

G E N E X                          

3 

 

 

BATTERY SAFETY INSTRUCTION            

                         

                            

CAUTION: 

To reduce the risk of fire or injury to persons, read and follow these instructions: 

1. 

Use only the following type and size of handset batteries: cordless Telephone Batteries  DC3.6V, 5 50mAh, 

Ni-MH AAA size Batte ry pack.    

2. 

Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special 

disposal instructions. 

3. 

Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or 

skin. It may be toxic if swallowed. 

4. 

Exercise care in handling the battery in order not to short the battery with conducting material such as rings, 

bracelets and keys. The battery or conductor may overheat and cause burns. 

5. 

  Recharge only the battery provided with or identified for use with this product. The battery may leak 

corrosive electrolyte or explode if it is not the correct type. 

6. 

Do not attempt to rejuvenate the battery provided with or identified for use with this product by heating them. 

Sudden release of the battery electrolyte m ay occur causing burns or irritation to eyes or skin. 

7. 

When inserting the batteries into this product, the proper polarity or direction must be observed. Reverse 

insertion of batteries can cause charging that may result in leakage or explosion. 

8. 

Remove the b atteries from this product if the product will not be used for a long period of time (several 

months or more) since during this time the battery could leak in the product. 

9. 

Discard “dead” batteries as soon as possible since “dead” batteries are more likely to leak in a product. 

10. 

Do not store this product, or the battery provided with or identified for use with this product, in high-

temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose of extending shelf life 

should be stabilized at room temperature prior to use after cold storage.

 

11. 

Disconnect telephone lines before installing batteries.

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for CT-D201



































Reviews:

No comments

Brands by name

Popular brands

Load more brands