Super Night Vision Camera
OPERATION MANUAL
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Note -
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / tv technician for help.
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Caution -
1. A regulated DC12V 5A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this product, or their
local government office, for details of where and how they can take item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract.
Household users should contact either the retailer where they for disposal.
SPECIFICATIONS
Model
Standard type
External Control type
Signal Format
NTSC
PAL
NTSC
PAL
Image Device
1/3" Sony Super HAD CCD
Ⅱ
Scanning System
2:1 Interlace
H.Resolution
550TV Lines
Scanning Frequency
H:15.734KHz,
V:59.94Hz
H:15.625KHz,
V:50Hz
H:15.734KHz,
V:59.94Hz
H:15.625KHz,
V:50Hz
Total Pixels
811(H) x 508(V)
795(H) x 596(V) 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V)
Electronic Shutter
1/60 sec
1/50 sec
1/60 sec
1/50 sec
S/N Ratio
More than 45dB(AGC Off)
Gnmma Correction
r=0.45
Min. Illuminationv
0 Lux (IR LED ON)
Sync. System
Internal
Second Video Connector
1.0 Vp-p Composite 75(Ω) unbalanced
LED
100 units Infrared LED
100 units Infrared LED
240 Units Infra LED
(With Illuminators Combination)
LED Full Angle
20 ~ 45 Degree Combination
LED Wavelength
850 nm
Lens Mount
f5~50mm IR Varifocal Lens(ICR)
Input Power Source
DC12V 1,5A /
AC24V 25W(1,5A) at Heater On
DC12V 1,5A /
DC12V 3A
(With Illuminators Combination)
AC24V 25W(1,5A) at Heater On
Operating Temperature
-10
℃
~+50
℃
(Heater on : -40
℃
~ +50
℃)
Storage Temperature
-20
℃
~ +60
℃
Humidity
10%RH ~ 60%RH
Dip Switch Function
BLC, ALC, FLICKERLESS, AGC,
MIRROR MODE, HOLD TIME, SENSITIVITY
Options
AC24V only,
Heater (on:+3.9
℃
/ Off:+15
℃
)
AC24V only, Heater,
Ex-View, Illuminator
Weight
Approx, 2.19kg
Approx, 1.8kg
Approx, 3kg
(With Illuminators Combination)
CONNECTION
• External Control Type
Standard Type
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
All manuals and user guides at all-guides.com
all-guides.com
