background image

8

Model 1137 Humidifier Installation Manual

Breathe Healthier! Residential Whole House Indoor Air Quality

Maintenance

Your Humidifier is engineered to give helpful and trouble-free humidification.  For maximum efficiency the following 

cleaning procedures should be carried out at the end of each heating season:
     
1.  Turn off water supply and electrical power to humidifier.

2.  Remove water distributor tube, distributor trough, used Vapor Pad

®

 and drain pan.  The Vapor Pad

®

 may be removed 

from either the top or bottom of the humidifier.  Clean excessive mineral deposits from the distributor trough,  drain 
pan and humidifier cabinet.  A solution of 1/2 vinegar & 1/2 water will help loosen mineral deposits.

3.  Insert a new 990-13 (GFI #7002) Vapor Pad

® 

(black notch on top).  Install trough and drain pan.  Replace the 

distributor tube to proper position over the distributor trough. Replace Vapor Pad

®

 yearly for peak performance.

4.  In heavy mineral areas, or if the solenoid valve fails to function, disconnect the 1/4” water supply line from the 

solenoid valve.  Remove the brass strainer body from the solenoid valve.  Carefully pull the strainer screen 990-17 
(GFI #7005) from the orifice fitting.  Clean the mineral deposits from all parts.   If the orifice is clogged, it may be 
opened by inserting a small needle.  Reinsert the filter into the orifice fitting and screw the brass strainer body into 
the solenoid valve.

5.  Reconnect the 1/4” water line to the solenoid valve if necessary.  Turn on the water supply and check all points for 

leakage.  The operation of the unit may be checked by starting the furnace.  The humidifier operates only when the 
furnace blower is running or the burner circuit is energized.  The humidifier is now ready for operation.

6.  During the summer, turn off water supply and electrical power to humidifier.  Close air damper.

Parts Drawing

SOLENOID VALVE

ASS'Y 990-53

1137-7 WIRING BRACKET

40-7 TINNERMAN NUT

1137-8 MOTOR

1137-50 COOLING FAN

GA4238 RELAY ASS'Y (FORMERLY 1137-26)

1137-39 FRONT COVER

ASS'Y

1137-3 DRAIN PAN

P-163 HOSE CLAMP

1099-16 DRAIN TUBE

P-103 COMPRESSION NUT

P-104 COMPRESSION SLEEVE

P-111 CONNECTOR

1137-38 CABINET ASSEMBLY

990-37-76 ORIFICE & STRAINER 

ASSEMBLY

990-16-76 ORIFICE FITTING

990-17 STRAINER SCREEN

990-18 STRAINER BODY

1137-2 FAN SHROUD

1137-9 FAN BLADE

1137-20 FAN GUARD

1137-24 DISTRIBUTOR TUBE

1099-9 THUMB NUT

1137-35 TROUGH COVER

1137-4 DISTRIBUTOR TROUGH

990-13 EVAPORATOR PAD

1137-31 POWER SUPPLY CORD

Summary of Contents for 1137 Series













Reviews: