General Music Pianovelle GPS2500, Service Manual

Page: 18 / 20

❒ ❒ ❒ ❒ ❒
18
DRW
APP.
CKD
WRITTEN CONSENT BY GENERALMUSIC.
OR REPRODUCE THIS DOCUMENT WITHOUT
ALL RIGHTS ARE RESERVED, NO COPIES
GENERALMUSIC S.p.A. ITALY
PART:
DWG#
DISK:
REV:
PCB#
Falconi
Boccato
Boccato
550129
20/12/96
42
Installation Instructions
Optional Accessories
1/1
Part List:
J1
Leave the jumper J1 on its position.
G
NOTE:
J2
J1
A
B
J2
Check that the jumper J2 [G] is set to position "B".
The operations can be carried out without removing the support [B].
B
A
I
Leave the jumper J2 on its position.
NOTE: the SIMM module compatibles are:
1 Mbyte (x8 or x9) 30-pin 70ns maximum access time.
16 Mbyte (x8 or x9) 30-pin 70ns maximim access time.
4 Mbyte (x8 or x9) 30-pin 70ns maximum access time.
The modules must be two.
J2
J1
F
A
B
NOTE:
J2
J1
1) N˚ 2 4Mbyte 70ns Dram module (Code 760994)
H
B
A
E
- Locate the CPU board [A].
- Insert the DRAM module [1] into the CPU’s CN5 connector[I].
KIT 970213 - Backed Samples Dram mounting instructions:
2) 2 buffer modules
8) 4 screws (M3x8)
Part List:
7) 2 contacts x 10cm cable
Audio/Video board NTSC
10 contacts x 65cm flat cable
6) 10 contacts x 40cm flat cable
5) 16 contacts x 7.5cm flat cable
4) 9 contacts x 15cm flat cable
3) 34 contacts x 7.5cm flat cable
1) Audio/Video board PAL
Leave the jumper J2 on its position.
JP1
(Code 841025)
(Code 120003)
JP2
1
D
J2
(Code 841009)
(Code 841019)
(Code 841049)
(Code 840204)
(Code 841004)
(Code 761093)
CN11
(Code 760994)
(Code 760993)
A
B
F
J1
B
on A position if the buffer modules
are installed, on B position if the
SIMM dram modules are intalled.
The jumper J1 [F] must be set
NOTE:
- Connect the cable [3] to the CPU board.
by means of the screw [8].
and to the CPU [A] and amplifier [D] boards.
- Connect the cables [3-4-5-6-7] to the AUDIO/VIDEO Board [1]
- Fix the AUDIO/VIDEO Board [1] to the threaded locations of the support [B]
- Locate the CPU Board [A] and insert the buffer modules [2] into the connectors [H].
- Check that the two jumpers JP1 e JP2 [E] are set to position "A"
and that the jumper J1 [F] is set to position "A".
65cm (GPS2500)
40cm (PS2500)
6
CN11
J2
J1
A
8
7
4
5
H
3
1
Brands generally accepted: SEAGATE, QUANTUM, HITACHI, CONNER,
Must be formatted using the procedure specified in the owner’s manual.
Dimensions: 2.5" Interface: IDE, or EIDE, or Fast ATA Size: to 540 MByte
KIT 970225 - Volatile SIMM Dram modules mounting instructions:
GPS-PS2500 & SK76
Check that the jumpers J1 [F] are set to position "B".
- Insert the Simm modules [2] into the CPU’s SIMM17-18 connectors [H].
The operations can be carried out without removing the support [B].
- Locate the CPU board [A].
2
IBM, WESTERN DIGITAL.
B
Hard disk specifications:
C
E
A
E
3) 2 mounting brackets (Code 171250)
optional Generalmusic hard disk.
DO NOT FORMAT THE DEVICE, because it is
supplied already formatted and filled with various
If you mount the optional Generalmusic hard disk
styles, samples and songs.
(Code 120113)
is not supplied with this kit. Hard Disks are avalaible from
NOTE: The optional Generalmusic Hard Disk (Code 970224)
special outlets with the same technical characteristics as the
4) 8 screws (M3x4)
2
5
5
starting from the extreme left end in order that 4 free pins remain
(Code 840824)
to the right of the connector, and the other end
(Code 761094)
Part List:
2) 44 contacts x 7.5 cm flat cable
1) 16Mbit DRAM module
to the CPU’s CN8 connector [D].
1
four screw [5] and fix the assembly to the threaded locations [E] by
- Fix the mounting brakets [4] to the Hard Disk [1] by means of the
- Insert the DRAM module [2] into the CPU’s CN9 connector [C].
- Connect one end of the jumper [3] to the Hard Disk connector,
means of the four screws [5].
- Replace the support [B].
5
4
3
KIT 970241 (PAL) - KIT 970245 (NTSC) - Audio/Video interface mounting instructions:
2
KIT 970207 - Hard disk installation kit mounting instructions:
- Locate the CPU board [A] and remove the support [B] by screwing the locking screws [6].
Hard disk rear connector.
B
JP2 A
JP1