General Monitors S4000CH Manual Download Page 44 | Manualshive

Page: 44 / 74

background image

Model S4000CH

36

shorted, the unit must be returned to the factory or authorized service center for service.

5.1.10 F11 Internal Error

ACTION

– An internal error has occurred. The unit must be returned to the factory for

service. The possible errors are internal voltages are not at their proper values.

5.1.11 F12 ARGC fault

This error can only occur if the ARGC is enabled. This error implies something is wrong with
the ARGC system (plunger stuck open or closed) or the sensor is poisoned.

ACTION

- The sensor and ARGC should be inspected. Recalibration removes the errors. If

recalibration does not remove the F12 error, the operator must inspect the ARGC and make
sure the gas tank is not empty, the gas line is not leaking, and the regulator is at the proper
setting. You can then apply the magnet over the display to clear the F12 error.

5.2 General Monitors’ Offices

Area

Phone/Email

UNITED STATES

26776 Simpatica Circle
Lake Forest, CA 92630

Phone: +1-949-581-4464. 800-446-4872
Email: [email protected]

IRELAND

Ballybrit Business Park
Galway
Republic of Ireland, H91 H6P2

Phone: +353-91-751175

SINGAPORE

No. 2 Kallang Pudding Rd.
#09-16 Mactech Building
Singapore 349307

Phone: +65-6-748-3488

MIDDLE EAST

PO Box 54910
Dubai Airport Free Zone
United Arab Emirates

Phone: +

971-4294 3640

Table 8: GM Locations

Additional locations can be found on our web site, www.MSAsafety.com

«
...
42
43
44
45
46
...
»

Summary of Contents for S4000CH











































































Reviews:

No comments

Related manuals for S4000CH

AVCCAM AG-HMR10

Brand: Panasonic Pages: 4

Brand: Waycon Pages: 4

Brand: Bang & Olufsen Pages: 12

Brand: DBI SALA Pages: 32

Brand: Hach Pages: 148

Brand: Labona Pages: 12

Brand: Front Runner Pages: 5

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: Thule Pages: 4

Brand: Sable Pages: 15

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

Brand: Farad Pages: 8

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: RECARO Pages: 20

ORBISPHERE 31 9 Series

Brand: Hach Pages: 150

Single Sensor Set

Brand: Revbox Pages: 10

Brand: Viking Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands