ROOM THERMOSTAT
ROOM THERMOSTAT PLACEMENT
Place your room thermostat in a room where you most use it as your
living area. For example: living room. Avoid installing the room
thermostat where there is a lot of air circulation such as door entry or
window edges. Also, do not place in places near heat units (central
heating system, fireplace, etc.) and places that receive direct
sunlight. We recommend that the room thermostat be placed at an
altitude of 50 cm to 150 cm from the floor. You can try a few places to
find the most suitable place.
BATTERY PLACEMENT
Remove your room thermostat from Wall hanger. Then remove the
battery housing from the back side of thermostat. Install 2 alkaline
batteries to battery housing. Please be sure the directions of
batteries. Hang your thermostat on the Wall hanger after assemble
battery housing back. Change the both batteries together.
Warning:
When the product is not used for a long time (more than 15
days), remove the batteries. Otherwise, malfunctions that will occur
are out of warranty.
Warning!
Please throw away dead batteries to trashes special only for
batteries.
50 cm-150 cm
min.50 cm
1
2
3
AAA
AAA
O
C
ENGLISH
GENERAL SPECIFICATIONS
HT120 SET is a wireless room thermostat. The user can adjust the
room thermostat with the requirement temperature and get more
comfortable and economic heating.
Sensitive temperature measuring ON/OFF Control
Heating calibration Wireless Connection
HT120 SET AND EQUIPMENTS
TECHNICAL DATA
Room Thermostat
Receiver
80mm / 80mm / 35mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o
0.5 C
o
o
(5 C) – (30 C)
1 Years (2 x AAA)
o
o
(-10 C) – (+50 C)
o
o
(-20 C) – (+60 C)
Dimensions
Operating Current
Operating Sensitivity
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
85mm / 90mm / 28.5mm
220V AC
7A (220V AC)
o
o
(-20 C) – (+60 C)
Dimensions
Operation Current
Relay NO Switching Current
Storage Temperature
Temperature Measurement Accuracy
HT120 SET USER MANUAL
HT120 SET
Room Thermostat
Threaded inserts and
Screws
Wall Hanger
Alkaline
Battery
Receiver
Holder
Receiver
Power Cable
Room Temperature
Boiler is working
ON/OFF and
Temperature Setting Button
RECEIVER
RECEIVER LED LIGHT COLOR EXPLANATIONS
RECEIVER PLACEMENT
The important thing to note for receiver placement is that avoiding
physical contact with boiler and protecting against materials such as
liquid, dust etc. You can place your receiver in boiler's cabinet without
physical contact with boiler or mount receiver to Wall.
RECEIVER SETUP
First, shut down electrical current which your boiler is connected
(fuse, power outlet etc.)
Connect one of the boiler connection cable to receiver as shown in
the Connection Scheme.
Connect other boiler connection cable end to boiler's room
thermostat input as shown in the boiler's user manual.
Input Receiver power cable first to receiver than to plug. If there is
no plug near your boiler, you can connect cable to your boiler's
connection fuse.
After finishing connections, turn on electrical current first, then turn
on your boiler.
If you want to deactivate your receiver, press manual button for 2
seconds then you should see orange light on receiver. After being
sure that your boiler is working, press same button and see orange
light disappeared.
Setup Room Thermostat to sync receiver with room thermostat.
Green
Green Flashing
Red
Red Flashing
Orange
Pressed to receiver sync button and waiting
for thermostat sync signal
Receiver synced with thermostat and Works
properly
Receiver has energy but no thermostat
synced.
Boiler shut down because no signal from
thermostat more than 22 minute.
On Manual Mode.
4
5
COM
NO
NC
1
2
3
1-Receiver Led Light
2-Sync Button:
Syncs modem and room thermostat.
3-Manual Usage Button:
Deactivates receiver and allows you to use
boiler manually.
4-Receiver Power Cable Input
5-Boiler Connection Cable Input
HT120 SET
USER MANUAL
generallife.com.tr
generallife.com.tr
DIGITAL ROOM THERMOSTAT
DIGITAL ROOM THERMOSTAT
