background image

8.ADJUSTMENT AND TEST BEFORE FLYING

19

20

F-16

F-16

Attention: 

Only after turning on the 
mix switch,then operating 
the vector nozzle. 

ON

If adjustment and test are 
approved byprevious work, 
then enjoy your fly.

After check everything before flight, as a beginner, we should pay attention 
to the following issues, to make sure our flight is successful.

1. When use radio controller, make sure switch on the transmitter 
    power firstly, then power on the receiver.
2. Before flight, under power on condition, push up and down the throttle 
    and check the motor/ESC work well.
3. Before flight, check well the plane's center of gravity. Correct CG is the 
    key factor of successful flight.
4. After take off, if any usual flight or hard to control, we should pull high the plane, 
    then trim to adjust according to the actual situation to maintain it level flight. 
5. When the transmitter automatic alarming, you must end your flight as soon 
    as possible and operate to its landing, to avoid the radio will be out of control 
    since of low voltage.
6. If any damage in flight, please purchase the spare parts from your 
    distributor to refer to www.lxhm.us to check.

Preflight

Summary of Contents for F-16 fighting falcon













Reviews: