background image

FCS16 RIP-R-STRIPPER

FORM GOM4240301, VERSION 3.1

8

5) Start  the  motor  according  to  the  instructions  as

outlined  in  this  manual  to  minimize  the  possibility  of

unexpected  blade/accessory  oscillation.  Unexpected

blade/accessory  oscillation  can  result  in  the  loss  of

machine control and the possibility of property damage

and/or personal injury.

6) Operate  the  RIP-R-STRIPPER  only  when/where

visibility  and  light  are  adequate  for  the  job  at  hand.

Work carefully. Always hold the operator handle firmly

with both hands. Wrap your fingers around the handle

grips, keeping them cradled between your thumbs and

fingers.  Always  determine  the  operator  handle  is  in

good  condition  and  free  of  moisture,  pitch,  oil  or

grease. Wear gloves to improve your grip. Never leave

the RIP-R-STRIPPER running unattended.

7) Stop  the  motor  while  moving  and/or  repositioning

the  RIP-R-STRIPPER  on  the  job  site.  Allowing    the

motor  to  remain  operating  substantially  increases  the

potential  for  property  damage  and/or  personal  injury.

Special care must be exercised on slippery conditions

and  on  difficult,  uneven  surfaces.  Watch  for  cracks,

high  spots  and  other  surface  irregularities.  Keep

proper footing and balance at all times. The normal use

of this machine is on level surfaces. Other terrains can

be  dangerous  and  should  be  avoided.  Only  properly

trained operators should attempt these techniques.

8) Because the RIP-R-STRIPPER is classified as a low

cost,  low  horsepower,  portable  type  machine,  it  is

limited  in  the  number  of  practical  and/or  suitable  job

applications.  A  particular  job  site,  actual  surface

conditions,  job  specifications  and  operator

skill/common sense may dictate that a different type of

machine (with characteristics of higher purchase cost,

being  mounted  to  a  carrier  vehicle,  with  greater

horsepower and less mobility), method and/or process

be  utilized  to  properly  complete  the  job  with  the

degree  of  efficiency  and  safety  required.  Contact  the

Customer Service Department for specific information

regarding  suitable  job  applications,  job  site  surface

conditions  and  operator  experience/skill/common

sense  recommendations  for  the  RIP-R-STRIPPER

BEFORE utilization. There is no charge for this service.

MAINTENANCE, REPAIR AND STORAGE.

1) Use only genuine, approved replacement parts and

accessories for maintenance and repair. Use of parts

and accessories manufactured by others can result in

property damage and/or personal injury.

2) Follow  the  Service  instructions  as  outlined  in  the

appropriate section of this manual.

3) Always  stop  the  motor  and  disconnect  the

extension  cord  BEFORE  checking  or  working  on  the

RIP-R-STRIPPER.

4) Always  properly  maintain  the  RIP-R-STRIPPER.

Frequently  check  all  fasteners  and  individual  parts.

Built  in  safety  features  are  effective  only  if  they  are

maintained  in  good  working  condition.  Replace  any

questionable part or assembly with a genuine, factory

approved,  replacement  part.  Do  not  forsake  proper

maintenance for the price of a few replacement parts.

Proper maintenance does not cost...it actually pays

dividends. Do not attempt any maintenance repair work

not  described  in  this  manual.  Have  such  work

performed at your dealer’s service facility.

5) Maintain  all  safety  and  operation  decals  in  proper

condition.  If  any  decal  becomes  damaged  and/or

unreadable, replace with a genuine, factory approved,

replacement part only.

6) The RIP-R-STRIPPER may utilize self locking type

hexagon head nuts to minimize the effects of vibration.

Replace all self locking hardware with genuine, factory

approved, replacement parts only. 

7) Consult  the  material  supplied  by  the  motor

manufacturer for specific information relative to proper

operational, lubrication and storage requirements.

Summary of Contents for RIP-R-STRIPPER FCS16
































































Reviews: