General Equipment RIP-R-STRIPPER FCS10GEN2, Operator'S Manual

Page: 8 / 27

FCS10GEN2 RIP-R-STRIPPER ® FLOOR COVERING STRIPPER
FORM GOM03042001US, VERSION 1.2
English-EN 7
6 MACHINE SPECIFICATIONS
FIGURE 3
FRAME STRUCTURE Unitized, welded steel plate.
DRIVE SYSTEM Random orbit, direct shaft mount.
NUMBER
ELASTOMERIC
RUBBER MOUNTS 4
NUMBER BLADE
OSCILLATIONS 3400 per minute
MAIN FRAME WIDTH 8-1/4 inches (210 mm)
MAIN FRAME LENGTH 23-1/4 inches (591 mm)
OPERATOR HANDLE
WIDTH
23-3/64 inches (585.4 mm)
OPERATING LENGTH 36-13/32 inches (924.8 mm)
OPERATING HEIGHT 43-1/2 inches (1105 mm)
WEIGHT 44 lbs (19.6 Kg), less blade.
ELECTRIC MOTOR 2300W, 115 VAC, 60 HZ, 15 Amperes
thermally protected.
EXTENSION CORDS Minimum rating for non-manufacturer supplied
extension cords SJTW 12 AWG/3C (3 x 3.31
mm 2 ) up to a maximum cord length of 75 feet
(22.9 M).
OPERATING
ENVIRONMENTS
Non-hazardous type locations.
REQUIRED NUMBER
OF OPERATORS 1
NOISE & VIBRATION EMISSIONS
Description North America Europe
Model FCS10GEN2
Noise Level 94 db
Vibration Level 6.2 m/s ²
RIP-R-STRIPPER POWER SOURCE
The RIP-R-STRIPPER is designed to operate from a clean, 15 ampere, 115
VAC, 60 Hz, nominal power source. Contact Customer Service Department for
information for operation from 220 VAC, 50 Hz power source. Clean power
refers to amperage available from individual electrical circuit selected.
Additional electrical products already using same circuit will reduce available
amperage resulting in starting/operational difficulties. Check proper voltage and
amperage levels in addition to power source being properly grounded.
Proper voltage and amperage to electric motor is essential for maximum
productivity and service life. Low voltage and amperage will cause motor to
overheat and can cause unrepairable damage to motor and related controls. An
improperly grounded circuit increases risk of electric shock. A qualified
electrician may need to be consulted.
IMPORTANT: Operating RIP-R-STRIPPER with improper voltage and/or
amperage will result in unrepairable damage to electric motor and related
controls.
7 STANDARD PRODUCT & ACCESSORIES
Refer to FIGURE 3 for overview description of standard components included
in machine. Included in shipment for FSC10GEN2 RIP-R-STRIPPER should be
the following:
1 each, Model FCS10GEN2 RIP-R-STRIPPER main frame assembly
1 each, Operator handle assembly
1 each, T-Handle Hex Key
1 each, 4 inch wide straight blade, part # FCS16-1100
1 each, 10 inch wide straight blade, part # FCS16-1300
1 each, Final inspection form
ACCESSORIES
NOTE: All blades are for use in general purpose projects on both wood and
cement surfaces unless otherwise designated.
Part # Description Weight
(in lbs)
FCS16-1050 Blade, scoring, 4 x 6 inch
wide, single bevel edge.
Cement surfaces ONLY.
0.4
FCS16-1100 Blade, straight, 4 inch x 6
inch, single bevel edged.
0.5
FCS16-1200 Blade, angled, 6 inch
wide, single beveled
edge. Cement surfaces
ONLY.
2.0
FCS16-1300 Blade, straight, 3 inch x
10 inch wide, single
beveled edge.
0.5
FCS16-1500 Blade, scoring, 8 inch
wide, beveled edge
FACING UP. For
removing glued carpet,
and sheet type linoleum,
rubber, PVC, etc., from
cement surfaces ONLY.
0.5
FCS16-1600 Blade, scoring, 8 inch
wide, beveled edge
FACING DOWN. For
removing glued carpet,
and sheet type linoleum,
rubber, PVC, etc., from
WOOD surfaces ONLY.
0.5
8 MACHINE SET-UP
Open the shipping carton immediately upon receipt. Remove RIP-R-STRIPPER
from cartons. Visually inspect contents for freight damage and/or missing parts.
If shipping damage is evident, contact delivering carrier immediately to arrange
for an inspection of damage by their claims representative. DO NOT DESTROY
OR DISCARD SHIPPING CARTON UNTIL INSTRUCTED BY AUTHORIZED
REPRESENTATIVE OF CARRIER OR FACTORY. If missing parts are
detected, notify your dealer who will assist you in obtaining them.
NOTE:
If ordered with RIP-R-STRIPPER, optional blades and accessories can
be shipped separately or included in shipping carton.
NOTE: RIP-R-STRIPPER is shipped from factory with operator handle
assembly uninstalled to main frame. All lubrication fittings are lubricated at
factory and will not require further servicing until first scheduled maintenance.