background image

 

4096-630 

General Dynamics Satcom Technologies

 

1.2M Ku-BAND Rx/Tx SERIES 1132 

 

 

 

 
 

 

12

SECTION III   

ANTENNA POINTING 

 
3.0 ANTENNA 

POINTING 

 
 

The 1.2 meter reflector contains a 17.3° elevation offset look angle.  Therefore, 
when the reflector aperture is perpendicular to the ground, the antenna is actually 
looking 17.3° in elevation.  Refer to Figure 2. 

 
Note:  The following alignment procedure is intended only as a general reference 

guide for this antenna.  For proper antenna performance, accurate 
alignment is critical.  Therefore, it is recommended that your own detailed 
procedure be used or contact General Dynamics Technical Support 
Department for additional recommendations. 

 
STEP 1: 

BEFORE ADJUSTING ELEVATION LOOSEN THE HARDWARE ON 
BOTH SIDES OF THE POSITIONER, REFER TO FIGURE 2 FOR 
LOCATION.  

Adjust the reflector up or down in elevation by turning the 

5/16” Bolt at the az/el positioner until the desired elevation is read on the 
side of the positioner.  This scale is used for nominal readings and is 
accurate to ±2 degrees.  

Note: Elevation rod is for adjustment only, it 

is not intended to be part of the structural integrity of the assembly, 
tightening the elevation rod is not necessary.

  Snug the hardware at 

the side of the positioner. 

 
STEP 2: 

Azimuth Adjustment:  With the electronics set to acquire the satellite, 
rotate the antenna in azimuth until the satellite is found.  Tighten the 
canister hardware at this time. 

 
STEP 3: 

Fine azimuth adjustment is achieved by 

loosening the three hex nuts

 

inside the Az/el positioner

 and turning the single hex bolt at the back of 

the positioner in either direction.

 Note: Azimuth rod is for adjustment 

only, it is not intended to be part of the structural integrity of the 
assembly, tightening the azimuth rod is not necessary.

 

 

STEP 4: 

Peak the antenna signal by fine adjustments made in both azimuth and 
elevation until the optimum signal is achieved. 

 
STEP 5: 

Tighten all hardware used for adjustment. 

 
 

Summary of Contents for 1.2M Ku-BAND RxSERIES 1132
















Reviews: