Generac Power Systems Stationary Emergency Generator, Owner'S Manual

Page: 57 / 144

EXPLODED VIEW: EV ENCLOSURE C2
DRAWING #: 0H0004
GROUP F
ITEM PART# QTY. DESCRIPTION
REVISION: J-1396-F Page 2 of 2
DATE: 1/23/12
(2)1 0G00450AL0R 1 REAR WRAP C2 CPL
(1)2 0C2454 44 SCREW THF M6-1 X 16 N WA Z/JS
(2)3 0F58490AL0R 2 DOOR C2
4 087233 2 RIVET POP .1875 X .450 SS
(1)5 0E3257 10 SCREW TH-FRM M6 W/CAP SHKPRF W
(2)6 0F58520AL0R 2 DISCHARGE DUCT LH & RH SIDE C2
(2)7 0F98330AL0R 2 FRONT CORNERS C2
(2)8 0F58510AL0R 1 DISCHARGE CENTER DUCT C2
9 049813 2 NUT HEX M6 X 1.0 G8 YEL CHR
(1)10 077992 17 NUT HEX LOCK M6-1.0 SS NY INS
(2)11 0F98350AL0R 1 ROOF C2
12 0F2786 2 SLITTER C4
13 0F2785 1 SPLITTER LOWER C4
14 0F3364 1 SPLITTER STINGER C2
15 0F4880 2 SUPPORT SPLITTER LH C2
16 0F5049 2 TAB PULL
17 0F4487A 1 ASSEMBLY COVER ACCESS
18 022473 7 WASHER FLAT 1/4-M6 ZINC
19 022097 5 WASHER LOCK M6-1/4
20 022127 1 NUT HEX 1/4-20 STEEL
21 0F3072 10 INSULATION RETAINMENT HANGER
22 078115 26 WASHER SELF LOCKING DOME #4-40
23 0G5892 2 INSULATION DOOR C2
24 0G5892A 1 INSULATION ROOF TOP
25 0F5048D 2 VISE-ACTION LATCH SLOTTED CIR
26 0E5968 1 GASKET EXTRUDED TRIM (328” LG)
27 0G5892D 2 INSULATION SPLITTER
28 0G5892C 2 INSULATION SPLITTER
29 0F4051C 2 INSULATION DUCT
30 0F3890B 4 RETAINER INSULATION (820)
31 0F4051B 2 INSULATION DUCT SIDES
32 0F3890 4 RETAINER INSULATION (450)
33 078115A 6 WASHER SELF LOCKING DOME #8-32
34 0G5892E 1 INSULATION LOWER SPLITTER
35 042568 2 SCREW HHC M6-1.0 X 20 G8.8
36 0912970094 2 ASSY WIRE 14 AWG 34.8" GRN/YEL
37 022447 2 WASHER SHAKEPROOF INT 1/4
38 0G5892B 1 INSULATION REAR WRAP
39 0F8869D 1 KEY VISE-ACTION LATCH SLOT CIR
40 0E5298L 1 FOAM 300 X 300 THERMAL ACO (APPLIES TO 4.2L UNITS ONLY)
41 066760 1 STRIP SEALANT 1/8 X 1 (44.52”LG)
42 0H1208A 1 RF COVER PLATE-PLASTIC-BISQUE
0H1208B 1 RF COVER PLATE-PLASTIC-GREY
49 0H0412 4 NUT U M6-1.0 GEOMET
50 0C8566 4 SCREW HHFC M6-1.0 X 20 G8.8
(1)ENCLOSURE NOTE: PANELS THAT FASTEN TO THE BASEFRAME (EXCEPT ITEM 1) AMUST BE SECURED USING I/N 2 & 5 (THREAD FORMING FASTENERS)
AND I/N 10 (LOCK NUT). LOCK NUT IS TO BE INSTALLED AFTER THREAD FORMING FASTENER HAS PENETRATED THROUGH EXTRUSIONS IN ENCLOSURE
PANELS. ALL PANEL TO PANEL CONNECTIONS TO INCLUDE AT LEAST ONE CONNECTION POINT USING I/N 5 (THREAD FORMING FASTENER).
(2) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
•
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO AS400 BOM.
•
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM FOR CORRECT MATERIAL
AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).