background image

SPECIFICATIONS

GENERATOR

Type ............................................................................. Synchronous
Rotor Insulation ................................................................... Class H
Stator Insulation .................................................................. Class H
Total Harmonic Distortion ......................................................< 3.5%
Telephone Interference Factor (TIF) ..........................................< 50
Alternator Output Leads 3-phase ........................................... 6-wire
Bearings .........................................................................Sealed Ball
Coupling .......................................................................Flexible Disc
Load Capacity (Standby Rating) ............................................60kW*
*

  NOTE: Generator rating and performance in accordance with ISO8528-5, BS5514, SAE J1349, 

ISO3046 and DIN 6271 Standards. KW rating is based on LPG fuel and may derate with natural 

gas.

Excitation System ....................................................................Direct
Generator Output Voltage/kW - 60 Hz 

kW 

Amp  CB Size

  120/240V, 1-phase, 1.0 pf 

60 

250 

300

  120/208V, 3-phase, 0.8 pf 

60 

208 

250

  277/480V, 3-phase, 0.8 pf 

60 

90 

100

Generator Locked Rotor KVA Available @ Voltage Dip of 35%
  Single-phase or 208 3-phase ............................................. 92 KVA
  480V, 3-phase .................................................................. 105 KVA

ENGINE

Cylinders and Arrangement ................................................ 6, V-type
Displacement ....................................................................... 3.0  Liter
Bore ...........................................................................89mm (3.5 in.)
Stroke ...................................................................79.5mm (3.13 in.)
Compression Ratio .............................................................10.5-to-1
Air Intake System ...............................................Naturally Aspirated
Lifter Type ............................................................ Shim Over Bucket

Engine Parameters

Rated Synchronous RPM ..............................................60 Hz, 3600
HP at rated kW ..................................................................60 Hz, 94

Exhaust System

Exhaust Flow at Rated Output 60 Hz .................................. 590 cfm
Exhaust Temperature at Rated Output ................................ 1050° F

Combustion Air Requirements

Flow at rated power, 60 Hz ................................................. 210 cfm

Governor

Type .................................................................................. Electronic
Frequency Regulation ...................................................Isochronous
Steady State Regulation ........................................................± 1/2%
Adjustments:
  Speed ............................................................................ Selectable

‹

‹

Engine Lubrication System

Type of Oil Pump ...................................................................... Gear
Oil Filter .............................................................Full Flow, Cartridge
Crankcase Oil Capacity .................................................6.5 U.S. qts.

COOLING SYSTEM

Type ....................................................................................... Closed
Water Pump .................................................................... Belt Driven
Fan Speed .........................................................................2180 rpm
Fan Diameter .....................................................................22 inches
Fan Mode ................................................................................ Puller
Air Flow (inlet air including alternator and
  combustion air) .......................................................... 4380 ft3/min.
Coolant Capacity ........................................................ (2.5 U.S. gal.)
Heat Rejection to Coolant ..........................................270,000 Btu/h
Maximum Operating Air Temp. on Radiator ..............60° C (150° F)
Maximum Ambient Temperature ................................50° C (140° F)

FUEL SYSTEM

Type of Fuel ......................................... Natural Gas, Propane Vapor
Carburetor ...................................................................... Down Draft
Secondary Fuel Regulator .................................................Standard
Fuel Shut-off Solenoid ........................................................Standard
Operating Fuel Pressure  ...................... 5 in. - 14 in. Water Column

Fuel Consumption - ft

3

/hr(Natural Gas/LPV)

 Exercise 

25% 

50% 

75% 

100%

 Cycle 

Load 

Load 

Load  Load

 123/48.2  260/101.9  500/196  700/274.4 960/376.3

*

   Engine is not field convertible between natural gas and propane. Jet size and ignition timing are 

factory set for the specific fuel.

ELECTRICAL SYSTEM

Battery Charge Alternator ............................................12V, 30 Amp
Static Battery Charger ............................................................2 Amp
Recommended Battery ................................................ 24F 525CCA
System Voltage .....................................................................12 Volts

Voltage Regulator

Type .................................................................................. Electronic
Sensing ........................................................................ Single-phase
Regulation ................................................................................± 1%
Features .................................................V/F Adjustable, Adjustable
 

Voltage and Gain LED Indicators

Power Adjustment for Ambient Conditions

Temperature Deration
  3% for every 10° C above °C ..................................................... 25
  1.65% for every 10° above °F .................................................... 77
Altitude Deration
  1% for every 100 m above m ................................................... 183
  3% for every 1000 ft. above ft. ................................................. 600

Controller .................................................R-200

‹

‹

‹

6-1

Standby Generator Sets

Specifications

GenSpec036  Rev.

 0  03/07

Summary of Contents for QT06030GNSNR









































































Reviews: