manualshive.com logo in svg

Generac Power Systems PowerPact 7.5 kW, Installation Manuallines

Share
Download
Generac Power Systems PowerPact 7.5 kW Installation Manuallines Download Page 22

Fuel Conversion/Gas Connections

18

Installation Guidelines for 60 Hz PowerPact™

Fuel Consumption

Generator

Natural Gas

LP Vapor

1/2 Load

Full Load

1/2 Load

Full Load

6 / 7.5 kW

73 / 2.07

117 / 3.31

0.87 / 3.29 / 31.6

1.42 / 5.37 / 51.6

* Natural gas is in ft

3

/h / cm

3

/h

** LP is in gal/h / l/h / ft

3

/h

*** Values given are approximate. Use the appropriate spec sheet or Owner’s Manual for specific values.
Verify gas meter is capable of providing enough fuel flow to include household appliances and all other loads.

NOTE: 

The gas supply and pipe MUST be sized at 100% load BTU / Megajoule rating.

Always refer to the Owner’s Manual for the proper BTU, Megajoule and required gas pressures:

•

Natural Gas:

BTU = ft

3

/h x 1000

Megajoules = m

3

/h x 37.26

•

Liquid Propane Vapor

BTU = ft

3

/h x 2500

Megajoules = m

3

/h / hour x 93.15

Summary of Contents for PowerPact 7.5 kW





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands