manualshive.com logo in svg

Generac Power Systems MLT4200IF4, Owner'S Manual, Page: 43 / 59

Share
Download
Generac Power Systems MLT4200IF4 Owner'S Manual Download Page 43

Troubleshooting

Owner’s Manual for MLT4200IF4 Light Tower

37

Section 5: Troubleshooting

General Troubleshooting

Some of the more common problems are listed in the
table below. This information is intended to be a check or
verification that simple causes can be located and fixed.
It does not cover all types of problems. Refer to the OEM
engine operator’s manual for additional troubleshooting
information.

 

Procedures that require in-depth knowledge

or skills should be referred to a Generac Mobile Products
Authorized Dealer.

If problems persist, contact Generac Mobile Products at 1-800-926-9768 for assistance.

(000139)

WARNING

Risk of burns. Allow engine to cool before 
draining oil or coolant. Failure to do so could 
result in death or serious injury.

Problem

Possible Cause

Solution

Unit cranks, but will not start

Fuel level low.
Fuel flow obstructed.
Fuel solenoid inoperable.
Air in fuel system.
Restricted air filter.
Glow plug(s) inoperable.

Check fuel level in tank.
Verify fuel pump operation.
Verify fuel solenoid operation.
Bleed air from fuel system.
Inspect air filter for blockage.
Inspect fuel supply hose from tank to fuel filter for cracks and 
abrasion.
Check for gelled fuel in fuel system in cold weather, especially at 
fuel filter.
Refer to OEM engine operator’s manual for additional 
information.

Unit starts, but stumbles and 
dies

Ambient temperature too 
low.
Intake heater inoperable.

Check if ambient temperature is within unit limits.
Check engine air inlet heater functionality.

High coolant temperature 
shutdown

Low coolant level.
Blockage in radiator.
Debris on radiator face.
broken coolant pump belt.
cooling fan inoperable.

Allow engine to cool, then check coolant level in radiator. Add 
coolant if needed.
Inspect radiator surroundings for blockage and remove any 
foreign matter.
Inspect for visible leaks. Verify tension of water pump drive belt.
Remove load on generator and restart engine. Verify coolant 
temperature and shut engine down immediately if it starts to 
overheat.

Low oil pressure shutdown

Oil level low.
Oil pump inoperable.

Check oil level. Add oil if necessary.

Unit stalls when export power 
is used

Load exceeds unit rating.

Turn outlet breaker ON and load sense switch OFF, confirm 
generator output is 60hz + or - 2hz. Reapply load.

The lights are flashing

Dusk-to-dawn sensor 
adjustment needed.
Generator frequency too 
low.

Adjust the dusk-to-dawn sensor to increase or decrease light 
received.
Turn off main breaker.
Check if AC frequency is >40hz.

To order go to Discount-Equipment.com

Summary of Contents for MLT4200IF4




























































Reviews:

No comments