background image

2

Generac

®

Power Systems, Inc.

Study these SAFETY RULES carefully before installing,
operating or servicing this equipment. Become familiar
with this Owner’s Manual and with the unit. The gener-
ator can operate safely, efficiently and reliably only if it
is properly installed, operated and maintained. Many
accidents are caused by failing to follow simple and fun-
damental rules or precautions.

Generac cannot anticipate every possible circumstance
that might involve a hazard. The warnings in this man-
ual, and on tags and decals affixed to the unit are, there-
fore, not all-inclusive. If using a procedure, work
method or operating technique that Generac does not
specifically recommend, ensure that it is safe for others.
Also make sure the procedure, work method or operat-
ing technique utilized does not render the generator
unsafe.

Despite the safe design of this generator, 
operating this equipment imprudently, neglecting
its maintenance or being careless can cause 
possible injury or death. Permit only responsible
and capable persons to install, operate or main-
tain this equipment.

Potentially lethal voltages are generated by these
machines. Ensure all steps are taken to render the
machine safe before attempting to work on the
generator.

Parts of the generator are rotating and/or hot
during operation. Exercise care near running gen-
erators. 

GENERAL HAZARDS

• For safety reasons, Generac recommends that this

equipment be installed, serviced and repaired by a
Generac Authorized Service Dealer or other compe-
tent, qualified electrician or installation technician
who is familiar with applicable codes, standards and
regulations. The operator also must comply with all
such codes, standards and regulations.

• Installation, operation, servicing and repair of this

(and related) equipment must always comply with
applicable codes, standards, laws and regulations.
Adhere strictly to local, state and national electrical
and building codes. Comply with regulations the
Occupational Safety and Health Administration
(OSHA) has established. Also, ensure that the gener-
ator is installed, operated and serviced in accordance
with the manufacturer’s instructions and recommen-
dations. Following installation, do nothing that might
render the unit unsafe or in noncompliance with the
aforementioned codes, standards, laws and regula-
tions.

• The engine exhaust fumes contain carbon monoxide

gas, which can be DEADLY. This dangerous gas, if
breathed in sufficient concentrations, can cause
unconsciousness or even death. For that reason, ade-
quate ventilation must be provided. Exhaust gases
must be piped safely away from any building or
enclosure that houses the generator to an area where
people, animals, etc., will not be harmed. This
exhaust system must be installed properly, in strict
compliance with applicable codes and standards.

• Keep hands, feet, clothing, etc., away from drive belts,

fans, and other moving or hot parts. Never remove
any drive belt or fan guard while the unit is operating.

• Adequate, unobstructed flow of cooling and ventilat-

ing air is critical to prevent buildup of explosive gases
and to ensure correct generator operation. Do not
alter the installation or permit even partial blockage
of ventilation provisions, as this can seriously affect
safe operation of the generator.

• Keep the area around the generator clean and unclut-

tered. Remove any materials that could become haz-
ardous.

• When working on this equipment, remain alert at all

times. Never work on the equipment when physically
or mentally fatigued.

!

!

!

!

DANGER

Important Safety Instructions

Guardian Liquid-cooled 15 kW, 20 kW and 25 kW Generators

SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe 
operation be copied and posted in potential hazard areas. Safety should be stressed to all
operators, potential operators, and service and repair technicians for this equipment.

!

!

SAVE THESE INSTRUCTIONS – This manual contains important instructions that should be
followed during installation and maintenance of the generator and batteries.

!

!

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

!

!

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

!

!

Summary of Contents for Guardian 004188-1





























































Reviews: