background image

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems, 
Inc.

®

 This model is a compact, high performance, air-cooled, engine 

driven generator designed to supply electrical power to operate 
electrical loads where no utility power is available or in place of utility 
due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the nearest 
Authorized Dealer for starting, operating and servicing procedures.

Throughout this publication, and on tags and decals affixed to the 
generator, DANGER, WARNING, CAUTION and NOTE blocks are 
used to alert personnel to special instructions about a particular 
operation that may be hazardous if performed incorrectly or carelessly. 
Observe them carefully. Their definitions are as follows:

DANGER

    After this heading, read instructions that, if 

not strictly complied with, will result in serious 
personal injury, including death and/or property 
damage.

    After this heading, read instructions that, if not 

strictly complied with, may result in serious 
personal injury and/or property damage.

    After this heading, read instructions that, if not 

strictly complied with, could result in damage to 
equipment and/or property.

NOTE:

    After this heading, read explanatory statements that require 

special emphasis.

These safety warnings cannot eliminate the hazards that they indicate. 
Common sense and strict compliance with the special instructions 
while performing the service are essential to preventing accidents.

Four commonly used safety symbols accompany the 

DANGER

WARNING

 and 

CAUTION

 blocks. The type of information each 

indicates is as follows:

  This symbol points out important safety 

information that, if not followed, could endanger 
personal safety and/or property of others.

  This symbol points out potential explosion 

hazard. 

   

  This symbol points out potential fire hazard.

 

 

  This symbol points out potential electrical shock 

hazard. 

The operator is responsible for proper and safe use of the 
equipment. We strongly recommend that the operator read this 
manual and thoroughly understand all instructions before using 
the equipment.

We also strongly recommend instructing other users to properly 
start and operate the unit. This prepares them if they need to 
operate the equipment in an emergency.

  Always disconnect spark plug wires and place 

the wires where they cannot contact the spark 
plugs to prevent accidental starting when 
setting up, transporting, adjusting or making 
repairs to the generator.

The generator produces dangerously high voltage that can cause 

extremely hazardous electrical shock. Avoid contact with bare 
wires, terminals, etc. Never permit any unqualified person to 
operate or service the generator.

Never handle any kind of electrical cord or device while standing 

in water, while barefoot or while hands or feet are wet. Dangerous 
electrical shock will result.

The National Electric Code requires the frame and external 

electrically conductive parts of the generator be properly connected 
to an approved earth ground. Local electrical codes may also 
require proper grounding of the generator. Consult with a local 
electrician for grounding requirements in the area.

Use a ground fault circuit interrupter in any damp or highly 

conductive area (such as metal decking or steel work).

Do not use worn, bare, frayed or otherwise damaged electrical 

cord sets with the generator.

Operate generator only on level surfaces and where it will not be 

exposed to excessive moisture, dirt, dust or corrosive vapors.

Gasoline is highly 

FLAMMABLE

 and its vapors are 

EXPLOSIVE

Do not permit smoking, open flames, sparks or heat in the vicinity 
while handling gasoline. Avoid spilling gasoline on a hot engine. 
Comply with all laws regulating storage and handling of gasoline.

Never add fuel while unit is running.

  Do not overfill the fuel tank. Always allow room 

for fuel expansion. If tank is over-filled, fuel can 
overflow onto a hot engine and cause FIRE or 
an EXPLOSION.

Never store generator with fuel in tank where gasoline vapors 

might reach an open flame, spark or pilot light (as on a furnace, 
water heater or clothes dryer). 

FIRE

 or 

EXPLOSION

 may result.

Generator exhaust gases contain 

DEADLY

 carbon monoxide gas. 

This dangerous gas, if breathed in sufficient concentrations, can 
cause unconsciousness or even death. Operate this equipment 
only in the open air where adequate ventilation is available.

Allow at least two (2) feet of clearance on all sides of generator or 

damage could be done to the unit. Never operate the unit inside 
any room or enclosure where the free flow of cooling air into and 
out of the unit might be obstructed. Review the “Cold Weather 
Operation” section.

DANGER

  NEVER operate the generator indoors, in an 

attached garage or near an open window.

1

Summary of Contents for 005396-0





































Reviews: