background image

7

* The notch and shelving filters adjustments, AutoCal

TM

 and GLM

TM 

manual system calibration features are part of the Genelec Loudspeaker Manager (GLM

TM

) software

AMPLIFIER SECTION

SIGNAL PROCESSING SECTION

SySTEM SPECIFICATIONS

1238CF

Lower cut-off frequency, –3 dB

< 55 Hz

Upper cut-off frequency, –3 dB

> 20 kHz

Free field frequency response

57 Hz – 20 kHz (± 2.0 dB)

Maximum short term sine wave acoustic 
output on axis in half space, averaged from 
100 Hz to 3 kHz

@ 1 m > 117 dB SPL 

Maximum long term RMS acoustic output 
in same conditions with IEC weighted noise 
(limited by driver unit protection circuit

@ 1 m > 107 dB SPL

Maximum peak acoustic output per pair with 
music material

@ 2 m  > 124 dB

Self generated noise level in half space at 1 m 
on axis (A-weighted)

< 15 dB

Harmonic distortion at 90 dB SPL at 1 m on 
axis 

Freq: 

60…100 Hz 

 

 

> 100 Hz

< 1 %
< 0.5 %

Drivers

Bass
Midrange
Treble

2 x 210 mm (8") cone
125 mm (5”) cone 
25 mm (1") metal dome 
All drivers are magnetically 
shielded

Weight

42 kg (93 lb)

Dimensions   

Height 
Width
Depth

 
610 mm (24”)
470 mm (18

1

/

2

”)

257 mm (10

1

/

8

”)

1238CF

Bass amplifier short term output power
Midrange amplifier short term output power 
Treble amplifier short term output power

Long term output power is limited by driver unit 
protection circuitry

150 W at 4 Ohm load
120 W at 8 Ohm load 
120 W at 8 Ohm load

Slew rate

80 V/us

Amplifier system THD at nominal output

< 0.05 %

Signal to Noise ratio, referred to full output

Bass 
Midrange 
Treble

 
>100 dB 
>100 dB 
>100 dB

Mains voltage
Mains voltage operating range

100/200 or 115/230 V
-10 to +10 %

Power consumption (average)

Idle
Full output

23 VA
330 VA

1238CF

Digital signal input connector
XLR female 110 kOhm

Digital signal output / Thru connector
XLR male 110 kOhm

Analog signal input connector
XLR female, balanced 10 kOhm

AES/EBU Single Wire or 
Dual Wire

AES/EBU Single Wire or 
Dual Wire

pin 1 gnd, pin 2 +, pin 3 -

Digital audio

Word length
Sample rate

16 - 24 bits
32 - 192 kHz

Control network

Type
Connection

Proprietary GLM™ network
2 RJ45, CAT5 cables

Crossover frequency

Bass/Mid
Mid/Treble

 
420 Hz 
2.8 kHz

GLM

TM

 software frequency response adjust-

ment *

Notch filters
Shelving filters

4 LF and 2 HF
2 LF and 2 HF

System calibration

Auto Cal™, Stand-alone

Figure 5: Horizontal directivity of the 1238CF.

Figure 4: Vertical directivity of the 1238CF.

Summary of Contents for 1238CFM









Reviews: