Gendex DenOptix QST Operator'S And Service Manual Download Page 52

Page: 52 / 68

User and Service Manual

Doc # M010-004WWE July 2005

Gendex DenOptix® QST

7.4

Disposal of waste materials and inoperative parts

Disposal regulations vary from country to country. Therefore, it is difficult to give specific

instructions on the disposal of DenOptix QST waste materials and inoperative parts. In gen-

eral, we believe the following guidelines to be true.

Material

Items

Recycle?

Comments

Plastic

Barrier Envelopes

Dispose of with other

Carousel Latches

non-recyclable plastic items.

Holders for I/O Plates

Aluminum

Housing, Optic Module

Yes

Remove all non-aluminum

Carousels

Yes

parts before recycling.

Scan Engine Frame

Yes

Carriage, Optic Module

Yes

Storage Phosphors

I/O Imaging Plates

Contain barium, which may be

Panoramic Imaging Plates

regulated. Contact your local

Ceph. Imaging Plates

Gendex for more information

on what to do with damaged

imaging plates.

Other Materials

All Others

All other materials should be

sent to a landfill.

Summary of Contents for DenOptix QST





































































Search results

Summary of Contents for DenOptix QST

Reviews:

Brands by name

Popular brands

Gendex DenOptix QST, Operator'S And Service Manual

Search results

Summary of Contents for DenOptix QST

Reviews:

Brands by name

Popular brands