background image

Installation Guide of the IOT Macro Gateway                                                        V0.1 
 

Gemtek Technology Co., Ltd.

 

In Commercial Confidential 

 

12/13 

5  Appendix 

 

 
FCC Statement 

 
 

Federal Communication Commission Interference Statement 

 
This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B 
digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to 
provide reasonable protection against harmful interference in a residential installation. 
This  equipment  generates  uses  and  can  radiate  radio  frequency  energy  and,  if  not 
installed and used in accordance with the instructions, may cause harmful interference 
to  radio  communications.  However,  there  is  no  guarantee  that  interference  will  not 
occur in a particular installation. If this equipment does cause harmful interference to 
radio  or television reception, which can be determined by  turning the equipment  off 
and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  of  the 
following measures: 
 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 
FCC  Caution:  Any  changes  or  modifications  not  expressly  approved  by  the  party 
responsible for compliance could void the user's authority to operate this equipment. 
 
This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the 
following two conditions: (1) This device may not cause harmful interference, and (2) 
this  device  must  accept  any  interference  received,  including  interference  that  may 
cause undesired operation. 
 

IMPORTANT NOTE: 
Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
minimum distance 

20cm

 between the radiator & your body. 

 

This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter. 
 
Country Code selection feature to be disabled for products marketed to the 
US/CANADA. 

Summary of Contents for WSMS-123














Reviews: