使用说明书
Operation
Instruction
0
.
05mm
4
.安装剪线电磁铁
(
1
)剪线电磁铁的行程:
A
.标准的行程为
4
.
6mm
.
B
.通过调节螺母
A
来调整行程。
(
2
)剪线电磁铁的调整
A
.电磁铁的安装位置以电磁铁工作时，凸轮左曲柄
③与凸轮右曲柄②之间有
0
.
5mm
间隙为标准。
B
.如需调整，可按图所示箭头方向移动电磁铁安装
架。
4
.
6mm
螺母
A
nut
A
电磁铁安装
架螺钉
electromagnet
mounts screw
电磁铁连接件
固定螺钉
e
fixed screw
lectromagnet link a
③
②
4
.
installation
of
thread
trimmer
(1)working
amount
of
the
thread
trimming
solenoid
.
A
.
The
standard
working
amount
of
the
thread
trimming
solenoid
is
4
.
6mm
.
B
.
By adjusting the nut to adjust A trip.
(2)adjusting
the
thread
trimming
solenoid
A
.
if
you
run
the
solenoid
under
this
circumstance
,
a
gap
of
0
.
5mm
occurs
between
the
left
crenk
③
and
the
right
crank
②.
This
state
is
the
standard
.
B
.
If you need to adjust
.
Can be shown as shown in figure and
direction of arrow mobile electromagnet mounts.
0.5mm
17.剪线机构的调整
Adjusting
for
thread
trimmer
(自动剪线型）
5
、安装剪线凸轮
(
1
)将主动轮上的第
2
标记点对准机壳上的定位标记
点。
(
2
)在启动剪线电磁铁状态下，朝正方向回转剪线凸
轮①直到接触滚柱，然后固定凸轮。
(
3
)剪线电磁铁关闭，使凸轮曲柄②恢复到原始置，
这样凸轮与滚柱端面将以
0
.
5
-
1
.
0mm
间隙为标准。
标记
point
A
0
.
5
-
1
.
0mm
5
thread trimming cam
(1) Align the second timing carved line of the pulley with
the arm' s carved line.
(2) Under the thread trimming solenoid is in operation,
rotate the trimming cam
①
clockwise and fix the cam when
it connected with the roller.
(3) When the thread cam following crank returned by
stopping the operation of the thread trimming
solenoid,
the edge end between the cam and the roller should be
from 0.5 to 1.0mm. It is the standard.
.Installation
of
①
0
.
6mm
②
11
Summary of Contents for GEM0311/0611D
