PAGE 08
PAGE 09
6.0
help you understand the coding procedure, here below is an example illustrating the configuration
procedure. In this case the code to be entered is 1-0-3.
- VEHICLE CODE PROGRAMMING
The system must be configured according to the specific vehicle model on which it is to be installed.
To
Press the vehicle remote control lock/unlock buttons to make sure the alarm system works properly.
If needed, disconnect the 8-pin connector and reconnect it after a few seconds.
A separate leaflet, included in the alarm packaging, lists all the available vehicles (codes
are updated at packaging time).
Up-to-date information on supported vehicle models can be found in the restricted area
of our website:
.
www.gemini-alarm.com
The alarm has an indicator LED that signals any wrong vehicle code inserted.
The code must range between 100 and 235 otherwise the LED on the unit blinks
repeatedly and the procedure is interrupted.
The previously inserted code remains stored.
The procedure is also invalidated if the LED blinks more than 10 times. In this case
there is no optical warning, the procedure is simply interrupted.
In either case, repeat the whole procedure.
!
!
Connect the wiring harness connectors to the corresponding alarm connectors.
Press and hold the button shown below until the LED lights up.
The LED will start flashing after 3 to 4 seconds; count the flashes.
In this case press the button at the 1st flash which corresponds to number “1”.
After 4 seconds, the LED will flash for the second time.
Press the button at the 10th flash which corresponds to number “0”.
After 4 more seconds, the LED will flash for the third and last time.
Press the button at the 3rd flash which corresponds to number “3”.
Release the button, the LED
will switch OFF.
Press
Press
Press
1st FLASH
10th
FLASH
3rd FLASH
3-4 seconds
When the last digit is entered, the alarm system “repeats” the entered code:
• 1 FLASH +
• 10 F
• 3 FLASHES
A SHORT PAUSE
A SHORT PAUSE
7.1
.
- OPTICAL SIGNALS
This function activates the optical signals (turn indicator flashes) that confirm system
arming/disarming
If the vehicle already has optical lock/unlock signals, the turn indicators alarm flashes
should be disabled.
7.2
7.3
7.4 -
.
Opening a door during the 60-second passive arming countdown
by the
- ACOUSTIC SIGNALS
- PASSIVE ARMING
DOOR SWITCH POLARITY SELECTION
This function activates the acoustic signals (siren chirps) that confirm system arming/disarming
This function arms the system 60 sec. after ignition is switched OFF and the last door is opened and
closed.
will cause the procedure to
interrupt; it will resume once the door is closed
This function modifies the alarm input signal (positive or negative) according to the signal generated
door switch.
.
!
DOUBLE PULSE UNLOCK QUICK ACTIVATION:
NB:
- Disconnect the alarm system power supply and ground the Green/Black wire.
- Connect the alarm power supply; 3 quick high-pitched chirps will confirm operation.
- Remove the Green/Black wire from ground.
To reset the default setting, repeat the above steps; 1 low-pitched chirp will confirm the operation.
7.5 - D
If this feature is enabled, 2 unlocking pulses will be supplied to unlock all doors at the same time.
This is useful in case separate actions are required to open the driver door and then the other doors.
OUBLE PULSE UNLOCK
7.0 - SYSTEM PROGRAMMING
The table below applies to the system programmed in “standard configuration”.
Every time you enter in programming mode, the alarm system resets to the default settings.
SELECTABLE FUNCTIONS
STATUS
LED FLASHES
Enabled
Disabled
Disabled
Enabled
Disabled
Arming/disarming optical signals
Arming/disarming acoustic signals
System passive arming
Door input - positive
Double pulse unlock
S
A lack of power during electrical system maintenance, will not affect the programming.
8.0 - SYSTEM PROGRAMMING EXAMPLE
To enter in programming mode proceed as follows:
• With the alarm system disarmed, turn ignition key “ON”.
• Wait approx. 2 sec. for the LED to light up.
• While the LED is ON, press remote control button “ON”.
Press Gemini remote control button “
” to enable programmable functions and button
“
” to disable them.
ON
OFF
