Gemalto Cinterion Hardware Interface Description Download Page 8 | Manualshive

Page: 8 / 70

background image

Cinterion

®

Java Terminals Hardware Interface Description

1 Introduction

16



EHSxT_BGS5T_HID_v02

2014-05-23

Confidential / Preliminary

1

Introduction

This document

1

describes the hardware of the Cinterion

®

Java Terminals. The Java Terminals

come in three variants depending on the included Cinterion

®

module and the available interfac-

es:

•

EHS5T RS485

contains a Cinterion

®

EHS5-E module and implements a USB 2.0 interface

with a USB-B connector as well as a 6-pole Western jack as plug-in power supply connec-
tor. Via a Weidmüller GPIO connectors it also implements a RS-485 interface including
power supply and ignition line.

•

EHS6T USB

contains a Cinterion

®

EHS6 module and implements a USB 2.0 interface with

a USB-B connector and also a V.24 / V.28 RS-232 interface with a D-sub 9-pole female
socket as well as a 6-pole Western jack as plug-in power supply connector.

•

BGS5T USB

contains a Cinterion

®

BGS5 module and implements a USB 2.0 interface with

a USB-B connector and also a V.24 / V.28 RS-232 interface with a D-sub 9-pole female
socket as well as a 6-pole Western jack as plug-in power supply connector.

Wherever necessary and appropriate this document distinguishes between these three vari-
ants.

gives a short overview of the available interfaces for the different Java Terminals.

The scope of this document includes interface specifications, electrical as well as mechanical
characteristics of the Java Terminals. It specifies standards pertaining to wireless applications
and outlines requirements that must be adhered to for successful product design. The Java
Terminals are compact GSM/UMTS modems for the transfer of data in GSM/UMTS networks.
Industrial standard interfaces and an integrated SIM card reader allow using the Java Termi-
nals easily as GSM/GPRS/UMTS terminals.

1. The document is effective only if listed in the appropriate Release Notes as part of the technical

documentation delivered with your Gemalto M2M product.

Table 1:

Cinterion

®

Java Terminals overview

Module/Interface

EHS5T RS485

EHS6T USB

BGS5T USB

Cinterion

®

m

odule

EHS5-E

EHS6

BGS5

RS-232 (Sub-D)

-





USB (USB-B)







Weidmüller connector
(GPIOs, SPI, I

2

C, RS-485)





(no RS-485)



(no RS-485,

no SPI)

Power supply (RJ-11)







RF antenna







«
...
6
7
8
9
10
...
»

Summary of Contents for Cinterion







































































Reviews:

No comments

Related manuals for Cinterion

All in One Printer

Brand: Baracoda Pages: 42

Brand: Mackie Pages: 2

Brand: Mackie Pages: 5

Brand: B+B SmartWorx Pages: 4

Brand: DBM Pages: 50

Brand: IBM Pages: 104

System Storage TS3100

Brand: IBM Pages: 375

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP DAS USA Pages: 8

Brand: ICP Pages: 14

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Paradyne Pages: 1

Brand: Allied Telesis Pages: 1

Brand: HARTING Pages: 13

Brand: Buffalo Pages: 2

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands