manualshive.com logo in svg

Gema PS07, Operating Instructions And Spare Parts List

Share
Download
Gema PS07 Operating Instructions And Spare Parts List Download Page 9

 

Rev. 00  02/17 

 

PS07 

Product description  

  9 

 

Product description 

 

 

Intended use 

 

The powder sieve machine is only intended for sieving powder which is 
used for coating. The powder sieve machine’s sieving capacity is 
supported by the sieve vibration motor. Depending on customer 
specifications, the powder is fed in by powder pumps or dense phase 
conveyor.  
 

 

fig. 1: Powder sieve machine PS07 

 

 

The powder sieve machine is certified for using in the following zone, if 
powder hoses are used, which grounding resistance is less than 
1 MOhm! 

 

Explosion protection 

Zone 

 

 II 3 D 

22 

 

Observance of the operating, service and maintenance instructions 
specified by the manufacturer is also part of conformity of use. This 
product should only be used, maintained and started up by trained 
personnel, who are informed about and are familiar with the possible 
hazards involved. 

Summary of Contents for PS07





































Reviews:

No comments

Brands by name

Popular brands

Load more brands