manualshive.com logo in svg

GEM 539 eSyDrive, Operating Instructions Manual

Share
Download
GEM 539 eSyDrive Operating Instructions Manual Download Page 29

16 Troubleshooting

Error

Possible cause

Troubleshooting

The product leaks downstream (doesn't

close or doesn't close fully)

Operating pressure too high

Operate the product with operating

pressure specified in datasheet

Valve body leaks or is damaged

Check valve body for potential damage,

replace valve body if necessary

The product doesn't close or doesn't

close fully

The actuator design is not suitable for the

operating conditions

Use an actuator that is designed for the

operating conditions

Foreign matter in the product

Remove and clean the product

Voltage is not connected

Connect voltage

The product doesn't open or doesn't open

fully

Actuator defective

Replace the actuator

Operating pressure too high

Operate the product with operating

pressure specified in datasheet

Foreign matter in the product

Remove and clean the product

The actuator design is not suitable for the

operating conditions

Use an actuator that is designed for the

operating conditions

Voltage is not connected

Connect voltage

Cable ends incorrectly wired

Wire cable ends correctly

The product leaks between actuator and

valve body

Bolting between valve body and actuator

loose

Retighten bolting between valve body and

actuator

Actuator/valve body damaged

Replace actuator/valve body

The product leaks between actuator

flange and valve body

Mounting parts loose

Retighten mounting parts

Valve body / actuator damaged

Replace valve body/actuator

Body of the GEMÜ product is leaking

Body of the GEMÜ product is faulty or

corroded

Check the body of the GEMÜ product for

potential damage, replace body if

necessary

Incorrect installation

Check installation of valve body in piping

Valve body connection to piping leaks

Incorrect installation

Check installation of valve body in piping

LED 1 is not lit

No initialisation

Initialise valve

Supply voltage too low

Check supply voltage

LED 1 lights up yellow

Set value signal outside of the area

Check set value signal

Temperature error

Check temperature

LED 1 flashes yellow

Actual value signal outside of the area

Check actual value signal

LED 1 and 2 are flashing yellow and red

simultaneously

No calibration

Contact GEMÜ

Internal error

Contact GEMÜ

16 Troubleshooting

www.gemu-group.com

29 / 34

GEMÜ 539

Summary of Contents for 539 eSyDrive



































Reviews:

No comments

Brands by name

Popular brands

Load more brands