manualshive.com logo in svg

Gelec PIT70000, User'S & Technical Manual, Page: 27 / 30

Share
Download
Gelec PIT70000 User'S & Technical Manual Download Page 27

                                                                                                                              

User’s & Technical Manual –

 P/I LEVEL TRANSMITTER PIT7000 

 

GELEC

  

Industrial Electronics

 

                                                                                                                                                                       PAGE

 

27

 

RESET TO DEFAULT SETTINGS 

 
The default factory calibration settings can be restored with the following procedure.  

 

 

Turn off the power supply of PIT7000 (STATUS LED is OFF).

 

 

Press and hold CALIBRATION BUTTON when power supply is off. 

 

While  still pressing,  turn on power  and  wait until the LED starts  flashing GREEN/RED. 
Flashing GREEN/RED means that settings are reset. Release the button. 

✓

 

Settings  are  reset  to  default.  PIT7000  returns  in  Normal  Operation  (STATUS  LED 
constant GREEN).

 

 

 
 

12.

 

DIMENSIONS 

 
 
 

 

 

 
 
 
 
 

Summary of Contents for PIT70000































Reviews:

No comments